{"title":"AdBlue Pumps \u0026 Transfer Kits","description":"\u003cp\u003eAdBlue pumps and transfer kits move diesel exhaust fluid (DEF) from IBCs, drums and tanks into trucks, tractors and machinery. Depots and workshops usually run an electric or air operated IBC kit, while a hand pump suits occasional drum work or a backup. Power source is the first decision: battery, 240V mains, compressed air or hand operation. Then decide between a bare pump and a complete kit with hose, nozzle and sometimes a meter.\u003c\/p\u003e\u003cp\u003eEvery wetted part has to be AdBlue compatible. A general-purpose pump with brass or cast iron internals corrodes in DEF, and the contamination it sheds can damage an SCR system downstream. Pick your power source from the guide below to narrow the list.\u003c\/p\u003e","products":[{"product_id":"af-fp-101320","title":"AF-FP-101320 Pro 240V AdBlue Transfer Kit for IBC, Auto Nozzle \u0026 Digital Flow Meter","description":"\u003cp\u003eDispensing AdBlue from a 1000 L IBC with a make-do setup is slow, messy and impossible to track. The Bluequip AF-FP-101320 Pro kit turns that into a proper metered dispensing point, built around a self-priming 240V pump on a stainless-steel IBC bracket.\u003c\/p\u003e\n\u003cp\u003eThe pump is a self-priming 240V unit rated at 35 lpm, mounted on a stainless-steel IBC bracket that holds the whole setup stable and supported rather than hanging off zip ties and bent brackets. A bottom suction kit draws the IBC down reliably, which keeps flow consistent and avoids the mid-fill stalls a poor pickup causes.\u003c\/p\u003e\n\u003cp\u003eWhat makes it the Pro kit is control. An automatic shut-off nozzle helps prevent overfills, and a K24 digital flow meter shows exactly what goes into each tank, which turns AdBlue from a vague consumable into a measured input you can track for cost, jobs and waste. It ships with a 6 m by 3\/4in hose, long enough to reach from the IBC to most fill points without dragging the unit around.\u003c\/p\u003e\n\u003cp\u003eFluid rated for AdBlue\/DEF. It is built for SCR-equipped fleets, farm machinery and multi-asset sites dispensing AdBlue, and its stainless bracket and AdBlue-compatible path keep the setup clean. It is an AdBlue kit and is not for diesel or oils.\u003c\/p\u003e\n\u003cp\u003eIt runs on 240V mains, so it is a fixed workshop or shed dispensing point rather than a vehicle-powered unit, and it mounts to a standard 1000 L IBC. Site it within reach of a 240V supply and position the IBC so the 6 m hose covers your fill points.\u003c\/p\u003e","brand":"Bluequip","offers":[{"title":"Default Title","offer_id":45482913529935,"sku":"AF-FP-101320","price":2627.0,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0711\/9110\/1519\/files\/bluequip-af-fp-101320-pro-240v-adblue-transfer-kit-for-ibc.webp?v=1785301351"},{"product_id":"af-fp-3322a50","title":"AF-FP-3322A50 Bluequip Heavy Duty Stainless Steel AdBlue Hand Pump Kit, 38 lpm","description":"\u003cp\u003e\u003cstrong\u003eCompatibility note: Dedicated to AdBlue (DEF). Using the pump for diesel, oil or other fluids will contaminate any AdBlue it pumps afterwards. A-FLO does not publish the drum bung thread, so confirm it suits your container before ordering.\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e38 lpm, by hand, in stainless steel. That combination puts this pump between a slow plastic drum pump and a powered transfer kit: fast enough to fill a truck's AdBlue tank without a long wait, with no power supply or air line needed at the drum.\u003c\/p\u003e\n\u003cp\u003eThe outcome is a pump that primes itself and dispenses immediately, at up to 38 lpm. Its stainless steel build uses materials A-FLO states are fully compatible with AdBlue, and its close manufacturing tolerances and wear-resistant materials are what A-FLO relies on for long service in daily use. The pump is made in Italy.\u003c\/p\u003e\n\u003cp\u003eIt suits sites dispensing AdBlue from drums where volumes justify a faster, longer-lived pump than a polypropylene hand pump, but not yet a 240V system.\u003c\/p\u003e\n\u003cp\u003eFluid rated for: AdBlue (DEF). Not for diesel, oils or other fluids. Connection: the drum bung thread and adaptor standard are not published, so check your drum's bung before ordering. No standard such as ISO 22241 is cited for the pump.\u003c\/p\u003e\n\u003cp\u003eThe kit is supplied complete with a suction tube, delivery hose and nozzle, ready to fit to the drum. The drum and AdBlue are not included, and no power or air supply is required.\u003c\/p\u003e\n\u003cp\u003eFor one- or two-vehicle operations where cost matters more than flow, the AF-FP-332080 Bluequip rotary drum pump kit is the polypropylene alternative. Where AdBlue comes in 1000L IBCs, the AF-FP-101320 Pro 240V AdBlue transfer kit adds an automatic nozzle and digital flow meter.\u003c\/p\u003e","brand":"Bluequip","offers":[{"title":"Default Title","offer_id":67699730972751,"sku":"AF-FP-3322A50","price":497.0,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0711\/9110\/1519\/files\/bluequip-af-fp-3322a50-adblue-hand-pump-kit-drum-view.png?v=1792020782"},{"product_id":"af-fp-332080","title":"AF-FP-332080 Bluequip Rotary Action Barrel Pump Kit, Adjustable Drum Adaptor, 2m Hose","description":"\u003cp\u003e\u003cstrong\u003eCompatibility note: Keep the pump dedicated to AdBlue (DEF), as any diesel or oil left in it will contaminate the AdBlue. A-FLO describes the polypropylene pump as resistant to various industrial-grade fluids but does not publish a specific AdBlue compatibility statement or flow rate.\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eOne or two vehicles, one drum, a few litres at a time: at that scale, AdBlue dispensing needs a clean, sealed transfer into the vehicle tank rather than a powered system. A rotary hand pump does the job with no power, no air and nothing to maintain beyond the pump itself.\u003c\/p\u003e\n\u003cp\u003ePouring AdBlue from an open drum or using a pump that has seen diesel puts contamination straight into the SCR system. This kit seals into the drum through its adjustable drum adaptor, which suits most drums, and transfers by turning the rotary handle, through a 2 m delivery hose to a stainless steel spout. The pump body is heavy duty polypropylene.\u003c\/p\u003e\n\u003cp\u003eA-FLO positions the kit for smaller operations running one or two vehicles and drawing AdBlue from 205L drums, where a powered system would sit idle most of the week.\u003c\/p\u003e\n\u003cp\u003eThe kit comes with the rotary pump, 2 m delivery hose, stainless steel spout and an adjustable drum adaptor to suit most drums. The drum and AdBlue are not included, and no power or air supply is required.\u003c\/p\u003e\n\u003cp\u003eWhere daily volumes outgrow a polypropylene pump, the \u003ca href=\"\/products\/af-fp-3322a50\"\u003eAF-FP-3322A50\u003c\/a\u003e Bluequip stainless steel hand pump delivers up to 38 lpm and is made in Italy. For IBC supply, the \u003ca href=\"\/products\/af-fp-101320\"\u003eAF-FP-101320\u003c\/a\u003e Pro 240V AdBlue transfer kit adds an automatic nozzle and digital flow meter.\u003c\/p\u003e","brand":"Bluequip","offers":[{"title":"Default Title","offer_id":67699733561423,"sku":"AF-FP-332080","price":344.0,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0711\/9110\/1519\/files\/bluequip-af-fp-332080-rotary-barrel-pump-kit-drum-view.png?v=1792020782"},{"product_id":"af-fp-101330","title":"AF-FP-101330 Basic 240V AdBlue Transfer Kit for IBC, Manual Nozzle, No Meter, 35 lpm","description":"\u003cp\u003e\u003cstrong\u003eCompatibility note: This kit has a manual nozzle and no flow meter, so it will not stop automatically when the tank is full or record litres dispensed.\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eThe AF-FP-101330 is the simplest way to put a 240V AdBlue dispensing point on a 1000L IBC. A self-priming 35 lpm pump sits on a stainless steel IBC bracket with a built-in nozzle holder, and a bottom suction kit draws from the IBC outlet.\u003c\/p\u003e\n\u003cp\u003eSelf-priming means the pump pulls AdBlue up from the IBC on start-up without being filled by hand first. The 6 m by 3\/4\" ID hose reaches most fill points from the IBC, and the stainless bracket keeps the setup off the ground and clear of contamination.\u003c\/p\u003e\n\u003cp\u003eIt suits workshops and yards that fill a small number of vehicles and do not need to track AdBlue use by vehicle or job.\u003c\/p\u003e\n\u003cp\u003eFluid rated for: AdBlue (DEF). Not for diesel, oils or other fluids.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eAt a glance:\u003c\/strong\u003e 240V, self-priming, 35 lpm | 6 m x 3\/4\" ID hose, manual nozzle | stainless steel IBC bracket, bottom suction kit\u003c\/p\u003e\n\u003cp\u003eSupplied with pump, stainless IBC bracket and nozzle holder, manual nozzle, 6 m hose and bottom suction kit. The IBC and AdBlue are not included. Site it within reach of a 240V outlet.\u003c\/p\u003e\n\u003cp\u003eTo meter every fill, the \u003ca href=\"\/products\/af-fp-101320\"\u003eAF-FP-101320\u003c\/a\u003e Pro kit adds a digital flow meter and automatic shut-off nozzle on the same stainless bracket. For a protected technopolymer housing, see the \u003ca href=\"\/products\/af-fp-201b103\"\u003eAF-FP-201B103\u003c\/a\u003e Premium kit.\u003c\/p\u003e","brand":"Bluequip","offers":[{"title":"Default Title","offer_id":67766784983119,"sku":"AF-FP-101330","price":2310.0,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0711\/9110\/1519\/files\/bluequip-af-fp-101330-basic-240v-adblue-transfer-kit.png?v=1793486665"},{"product_id":"af-fp-201b103","title":"AF-FP-201B103 Premium 240V AdBlue IBC Pump Kit, PIUSI A60 Auto Nozzle \u0026 K24 Meter, 35 lpm","description":"\u003cp\u003e\u003cstrong\u003eCompatibility note: The 240V pump runs on a 20 minute working cycle, so allow it to rest between long transfers.\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eThe AF-FP-201B103 is an enclosed, fully metered AdBlue dispenser for 1000L IBCs. It pairs a 35 lpm Suzzarablue AC pump with a PIUSI A60 automatic shut-off nozzle and a PIUSI K24 digital flow meter, so every fill stops when the tank is full and is counted in litres.\u003c\/p\u003e\n\u003cp\u003eThe kit is built around a Suzzarablue AC pump inside a shock-resistant technopolymer casing that protects the pump and fittings on the IBC. A mechanical IBC lock secures the dispenser to the tank, the ergonomic handle makes it easy to lift on and off, and a groove in the casing stores the 6 m hose neatly between fills.\u003c\/p\u003e\n\u003cp\u003ePIUSI designs the A60 nozzle to be light and ergonomic, with a body, lever, spout and break-away system built for impacts and daily handling. The K24 meter gives a litre reading per fill, useful for charging AdBlue to jobs or tracking use by vehicle.\u003c\/p\u003e\n\u003cp\u003eFluid rated for: AdBlue (DEF). Not for diesel, oils or other fluids.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eAt a glance:\u003c\/strong\u003e 230\/240V AC, up to 35 lpm, 20 minute working cycle | PIUSI A60 auto nozzle, PIUSI K24 meter, 6 m hose | technopolymer casing with IBC lock\u003c\/p\u003e\n\u003cp\u003eSupplied as a complete dispenser ready to lock onto the IBC. The IBC and AdBlue are not included. Site it within reach of a 240V outlet.\u003c\/p\u003e\n\u003cp\u003eFor the same Premium kit with the meter built into the nozzle, see the \u003ca href=\"\/products\/af-fp-201b103m\"\u003eAF-FP-201B103M\u003c\/a\u003e. For an open stainless-bracket setup, the \u003ca href=\"\/products\/af-fp-101320\"\u003eAF-FP-101320\u003c\/a\u003e Pro kit.\u003c\/p\u003e","brand":"Bluequip","offers":[{"title":"Default Title","offer_id":67766788456527,"sku":"AF-FP-201B103","price":3339.6,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0711\/9110\/1519\/files\/bluequip-af-fp-201b103-premium-240v-adblue-ibc-pump-kit.png?v=1793486665"},{"product_id":"af-fp-201b103m","title":"AF-FP-201B103M Premium 240V AdBlue IBC Pump Kit, PIUSI SB325 Metered Auto Nozzle, 35 lpm","description":"\u003cp\u003e\u003cstrong\u003eCompatibility note: The 240V pump runs on a 20 minute working cycle, so allow it to rest between long transfers.\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eThe AF-FP-201B103M is the Premium enclosed AdBlue dispenser with the meter moved into the nozzle. A PIUSI SB325 metered automatic nozzle shuts off when the tank is full and shows the litres dispensed right where the operator is looking.\u003c\/p\u003e\n\u003cp\u003eWith the meter in the nozzle there is no separate in-line meter on the hose, which keeps the setup compact. The 35 lpm Suzzarablue AC pump does the work inside the same technopolymer casing as the standard Premium kit.\u003c\/p\u003e\n\u003cp\u003eThe kit is built around a Suzzarablue AC pump inside a shock-resistant technopolymer casing that protects the pump and fittings on the IBC. A mechanical IBC lock secures the dispenser to the tank, the ergonomic handle makes it easy to lift on and off, and a groove in the casing stores the 6 m hose neatly between fills.\u003c\/p\u003e\n\u003cp\u003eFluid rated for: AdBlue (DEF). Not for diesel, oils or other fluids.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eAt a glance:\u003c\/strong\u003e 230\/240V AC, up to 35 lpm, 20 minute working cycle | PIUSI SB325 metered auto nozzle, 6 m hose | technopolymer casing with IBC lock\u003c\/p\u003e\n\u003cp\u003eSupplied as a complete dispenser ready to lock onto the IBC. The IBC and AdBlue are not included. Site it within reach of a 240V outlet.\u003c\/p\u003e\n\u003cp\u003eFor the Premium kit with an A60 auto nozzle and separate K24 in-line meter, see the \u003ca href=\"\/products\/af-fp-201b103\"\u003eAF-FP-201B103\u003c\/a\u003e. For an open stainless-bracket setup, the \u003ca href=\"\/products\/af-fp-101320\"\u003eAF-FP-101320\u003c\/a\u003e Pro kit.\u003c\/p\u003e","brand":"Bluequip","offers":[{"title":"Default Title","offer_id":67766788587599,"sku":"AF-FP-201B103M","price":3339.6,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0711\/9110\/1519\/files\/bluequip-af-fp-201b103m-premium-240v-adblue-ibc-pump-kit.png?v=1793486665"},{"product_id":"af-fp-203010","title":"AF-FP-203010 Suzzarablue 240V AdBlue Diaphragm Transfer Pump, Self-Priming, 32 lpm","description":"\u003cp\u003e\u003cstrong\u003eCompatibility note: This is the bare pump. Hose, nozzle, meter and suction kit are not included.\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eThe AF-FP-203010 is the PIUSI Suzzarablue AC diaphragm pump, the same pump family used in Bluequip's Premium IBC kits, supplied on its own for building or repairing an AdBlue system. It moves up to 32 lpm on 240V.\u003c\/p\u003e\n\u003cp\u003eThe electric motor drives a diaphragm with no dynamic seals, which removes the shaft seal that usually wears and leaks first in AdBlue service. The body, rotor and gears are technopolymer, with materials chosen to comply with ISO 22241, the standard for AdBlue handling. It self-primes and has a built-in bypass valve.\u003c\/p\u003e\n\u003cp\u003eIt suits workshops replacing a worn pump or fitting AdBlue to a tank they already have. The pump runs on a working cycle of up to 20 minutes.\u003c\/p\u003e\n\u003cp\u003eFluid rated for: AdBlue (DEF), antifreeze and windscreen washer fluid. Not for diesel or oils.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eAt a glance:\u003c\/strong\u003e 240V, self-priming, up to 32 lpm, 20 minute working cycle | polypropylene body and diaphragm, no dynamic seals | on\/off switch, 2 m cable and plug, built-in bypass\u003c\/p\u003e\n\u003cp\u003eSupplied with on\/off switch, 2 m power cable with plug and hose connector. Add hose, a nozzle such as the \u003ca href=\"\/products\/af-ae-pax70adb\"\u003eAF-AE-PAX70ADB\u003c\/a\u003e stainless automatic nozzle, and a suction line to suit your tank.\u003c\/p\u003e\n\u003cp\u003eFor a ready-to-run IBC dispenser with this pump family, see the \u003ca href=\"\/products\/af-fp-201b103\"\u003eAF-FP-201B103\u003c\/a\u003e Premium kit. For 24V vehicle power, the \u003ca href=\"\/products\/af-fp-204010\"\u003eAF-FP-204010\u003c\/a\u003e.\u003c\/p\u003e","brand":"Bluequip","offers":[{"title":"Default Title","offer_id":67766788620367,"sku":"AF-FP-203010","price":988.9,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0711\/9110\/1519\/files\/bluequip-af-fp-203010-suzzarablue-240v-adblue-diaphragm-transfer-pump.png?v=1793486665"},{"product_id":"af-fp-204010","title":"AF-FP-204010 24V AdBlue Transfer Pump Kit, 6m Hose \u0026 Manual Swivel Nozzle, 35 lpm","description":"\u003cp\u003e\u003cstrong\u003eCompatibility note: Runs on 24V DC from truck or plant batteries. A drum or IBC suction kit is sold separately, and the nozzle is manual, not auto shut-off.\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eThe AF-FP-204010 brings AdBlue dispensing to 24V vehicles: a self-priming pump rated at 35 lpm, supplied with a 6 m by 3\/4\" Bluequip hose and a manual nozzle with swivel.\u003c\/p\u003e\n\u003cp\u003eRunning on 24V means it can be mounted on a service truck or plant trailer and powered from the vehicle, with no generator or mains supply needed on site. The swivel on the nozzle stops the hose kinking as you move between fill points.\u003c\/p\u003e\n\u003cp\u003eIt suits mobile service crews, earthmoving and mining sites refuelling plant in the field, and truck-mounted AdBlue tanks.\u003c\/p\u003e\n\u003cp\u003eFluid rated for: AdBlue (DEF). Not for diesel, oils or other fluids.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eAt a glance:\u003c\/strong\u003e 24V DC, self-priming, 35 lpm | 6 m x 3\/4\" hose, manual swivel nozzle | drum or IBC suction kit sold separately\u003c\/p\u003e\n\u003cp\u003eSupplied with pump, 6 m hose and manual swivel nozzle. Add a 205L drum or 1000L IBC suction kit to suit your container, and wire it with fused cable sized to the pump.\u003c\/p\u003e\n\u003cp\u003eFor 240V workshop power, see the \u003ca href=\"\/products\/af-fp-203010\"\u003eAF-FP-203010\u003c\/a\u003e Suzzarablue pump. For an automatic shut-off upgrade, the \u003ca href=\"\/products\/af-ae-pax70adb\"\u003eAF-AE-PAX70ADB\u003c\/a\u003e stainless steel nozzle.\u003c\/p\u003e","brand":"Bluequip","offers":[{"title":"Default Title","offer_id":67766791241807,"sku":"AF-FP-204010","price":1128.6,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0711\/9110\/1519\/files\/bluequip-af-fp-204010-24v-adblue-transfer-pump-kit.png?v=1793486665"},{"product_id":"af-fp-206p1723a","title":"AF-FP-206P1723A 240V AdBlue Submersible Pump, Regenerative Turbine, 35 lpm","description":"\u003cp\u003e\u003cstrong\u003eCompatibility note: This is a submersible pump that sits inside the tank. Hose, nozzle and meter are not included.\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eThe AF-FP-206P1723A is a heavy-duty 240V submersible pump for AdBlue, delivering up to 35 lpm from inside the tank.\u003c\/p\u003e\n\u003cp\u003eBecause it sits in the fluid, it pushes AdBlue up and out rather than drawing it through a suction line, so there is nothing to prime. A regenerative turbine gives steady pressure, an integrated pressure regulator keeps output consistent, and a built-in non-return valve holds fluid in the delivery line between fills.\u003c\/p\u003e\n\u003cp\u003eIt suits bulk AdBlue storage tanks and fixed dispensing setups where an externally mounted pump is not practical.\u003c\/p\u003e\n\u003cp\u003eFluid rated for: AdBlue (DEF). Not for diesel, oils or other fluids.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eAt a glance:\u003c\/strong\u003e 240V submersible, up to 35 lpm | regenerative turbine, integrated pressure regulator | built-in non-return valve\u003c\/p\u003e\n\u003cp\u003eSupplied as the bare pump. Add delivery hose, a nozzle such as the \u003ca href=\"\/products\/af-ae-pax70adb\"\u003eAF-AE-PAX70ADB\u003c\/a\u003e stainless automatic nozzle, and a \u003ca href=\"\/products\/f0040710a\"\u003eK24 AdBlue meter\u003c\/a\u003e if you want to record litres. Have 240V connections made by a licensed electrician where required.\u003c\/p\u003e\n\u003cp\u003eFor an external 240V pump, see the \u003ca href=\"\/products\/af-fp-203010\"\u003eAF-FP-203010\u003c\/a\u003e Suzzarablue diaphragm pump.\u003c\/p\u003e","brand":"Bluequip","offers":[{"title":"Default Title","offer_id":67766791307343,"sku":"AF-FP-206P1723A","price":1502.6,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0711\/9110\/1519\/files\/bluequip-af-fp-206p1723a-240v-adblue-submersible-pump-top-view.png?v=1793486665"},{"product_id":"af-ae-kp21m","title":"AF-AE-KP21M Air Operated AdBlue IBC Kit, 2:1 Pump, 4m Hose \u0026 Manual Nozzle, 40 lpm","description":"\u003cp\u003e\u003cstrong\u003eCompatibility note: Needs a compressed air supply, and an air regulator is not included. A-FLO recommends fitting one.\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eThe AF-AE-KP21M runs AdBlue from a 1000L IBC on workshop air. A 2:1 ratio air-operated pump delivers up to 40 lpm, and it comes with a pump mount bracket, bottom IBC suction kit, 4 m of Bluequip delivery hose and a manual nozzle.\u003c\/p\u003e\n\u003cp\u003eAir power suits workshops that already have a compressor and air lines but no convenient 240V outlet at the IBC, and there is no electric motor at the tank. The 2:1 ratio means the pump delivers fluid at about twice the air pressure you feed it.\u003c\/p\u003e\n\u003cp\u003eIt is the lowest-cost way in the Bluequip range to put a pumped dispenser on an IBC.\u003c\/p\u003e\n\u003cp\u003eFluid rated for: AdBlue (DEF). Not for diesel, oils or other fluids.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eAt a glance:\u003c\/strong\u003e air operated, 2:1 ratio, up to 40 lpm | 4 m hose, manual nozzle | pump mount bracket and bottom IBC suction kit; air regulator not included\u003c\/p\u003e\n\u003cp\u003eSupplied with pump, mount bracket, bottom IBC suction kit, 4 m hose and manual nozzle. Add an air regulator and connect to your air line. The IBC and AdBlue are not included.\u003c\/p\u003e\n\u003cp\u003eFor a spring-retractable reel and automatic nozzle, see the \u003ca href=\"\/products\/af-ae-kp2110a\"\u003eAF-AE-KP2110A\u003c\/a\u003e (10 m) or \u003ca href=\"\/products\/af-ae-kp2115a\"\u003eAF-AE-KP2115A\u003c\/a\u003e (15 m). For 240V power, the \u003ca href=\"\/products\/af-fp-101330\"\u003eAF-FP-101330\u003c\/a\u003e Basic kit.\u003c\/p\u003e","brand":"Bluequip","offers":[{"title":"Default Title","offer_id":67766791503951,"sku":"AF-AE-KP21M","price":2213.2,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0711\/9110\/1519\/files\/bluequip-af-ae-kp21m-air-operated-adblue-ibc-kit.png?v=1793486665"},{"product_id":"af-ae-kp2110a","title":"AF-AE-KP2110A Air Operated AdBlue IBC Kit, 10m Spring Retractable Hose Reel \u0026 Auto Nozzle, 40 lpm","description":"\u003cp\u003e\u003cstrong\u003eCompatibility note: Needs a compressed air supply, and an air regulator is not included. A-FLO recommends fitting one.\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eThe AF-AE-KP2110A is a complete air-operated AdBlue station for a 1000L IBC, with a 10 m spring retractable hose reel and an automatic nozzle. A 2:1 ratio pump delivers up to 40 lpm.\u003c\/p\u003e\n\u003cp\u003eThe spring reel pulls the hose back in after each fill, so it is off the floor, out of the way of forklifts and free of the grit that can contaminate AdBlue. The automatic nozzle shuts off when the vehicle tank is full, which prevents spills and overfills.\u003c\/p\u003e\n\u003cp\u003eIt suits fleet depots and workshops with an air supply that fill many vehicles from one IBC.\u003c\/p\u003e\n\u003cp\u003eFluid rated for: AdBlue (DEF). Not for diesel, oils or other fluids.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eAt a glance:\u003c\/strong\u003e air operated, 2:1 ratio, up to 40 lpm | 10 m spring retractable hose reel, automatic nozzle | pump mount bracket and bottom IBC suction kit; air regulator not included\u003c\/p\u003e\n\u003cp\u003eSupplied with pump, mount bracket, bottom IBC suction kit, 10 m hose reel and automatic nozzle. Plan a wall or frame position for the reel, add an air regulator and connect to your air line. The IBC and AdBlue are not included.\u003c\/p\u003e\n\u003cp\u003eFor more reach, see the \u003ca href=\"\/products\/af-ae-kp2115a\"\u003eAF-AE-KP2115A\u003c\/a\u003e (15 m reel). For a basic kit with 4 m hose, the \u003ca href=\"\/products\/af-ae-kp21m\"\u003eAF-AE-KP21M\u003c\/a\u003e.\u003c\/p\u003e","brand":"Bluequip","offers":[{"title":"Default Title","offer_id":67766793961551,"sku":"AF-AE-KP2110A","price":4661.8,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0711\/9110\/1519\/files\/bluequip-af-ae-kp2110a-air-operated-adblue-ibc-kit.png?v=1793486665"},{"product_id":"af-ae-kp2115a","title":"AF-AE-KP2115A Air Operated AdBlue IBC Kit, 15m Spring Retractable Hose Reel \u0026 Auto Nozzle, 40 lpm","description":"\u003cp\u003e\u003cstrong\u003eCompatibility note: Needs a compressed air supply, and an air regulator is not included. A-FLO recommends fitting one.\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eThe AF-AE-KP2115A is a complete air-operated AdBlue station for a 1000L IBC, with a 15 m spring retractable hose reel and an automatic nozzle. A 2:1 ratio pump delivers up to 40 lpm.\u003c\/p\u003e\n\u003cp\u003eThe spring reel pulls the hose back in after each fill, so it is off the floor, out of the way of forklifts and free of the grit that can contaminate AdBlue. The automatic nozzle shuts off when the vehicle tank is full, which prevents spills and overfills.\u003c\/p\u003e\n\u003cp\u003eIt suits fleet depots and workshops with an air supply that fill many vehicles from one IBC and need extra reach across a wide bay.\u003c\/p\u003e\n\u003cp\u003eFluid rated for: AdBlue (DEF). Not for diesel, oils or other fluids.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eAt a glance:\u003c\/strong\u003e air operated, 2:1 ratio, up to 40 lpm | 15 m spring retractable hose reel, automatic nozzle | pump mount bracket and bottom IBC suction kit; air regulator not included\u003c\/p\u003e\n\u003cp\u003eSupplied with pump, mount bracket, bottom IBC suction kit, 15 m hose reel and automatic nozzle. Plan a wall or frame position for the reel, add an air regulator and connect to your air line. The IBC and AdBlue are not included.\u003c\/p\u003e\n\u003cp\u003eFor a shorter run, see the \u003ca href=\"\/products\/af-ae-kp2110a\"\u003eAF-AE-KP2110A\u003c\/a\u003e (10 m reel). For a basic kit with 4 m hose, the \u003ca href=\"\/products\/af-ae-kp21m\"\u003eAF-AE-KP21M\u003c\/a\u003e.\u003c\/p\u003e","brand":"Bluequip","offers":[{"title":"Default Title","offer_id":67766793994319,"sku":"AF-AE-KP2115A","price":4814.7,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0711\/9110\/1519\/files\/bluequip-af-ae-kp2115a-air-operated-adblue-ibc-kit.png?v=1793486665"},{"product_id":"24g745","title":"24G745 SD Blue Husky 515 PP Diaphragm Pump, 3\/4\" BSPP","description":"\u003cp\u003eThe 24G745 is the SD Blue version of the polypropylene Husky 515, set up for DEF\/AdBlue with PTFE diaphragms, fluoroelastomer balls and 3\/4\" BSPP fluid ports. The \u003ca href=\"\/products\/d5b911\"\u003eD5B911\u003c\/a\u003e shares the body with PTFE balls, 1\/2\" BSPT ports and a higher pressure rating. Choose it for 1\/2\" pipework or other chemicals. For the rest of the Husky range, see \u003ca href=\"\/collections\/air-operated-transfer-pumps\"\u003eair operated transfer pumps\u003c\/a\u003e.\u003c\/p\u003e\u003cp\u003eGraco recommends the SD Blue AODD pump over its LD Blue electric pumps for longer dispense runs, up to 61 m. The stall-free, low-pulsation air valve changes over smoothly, bolt-through fluid covers are designed to eliminate leaks, and there are no mechanical seals to fail. Typical sites include dealerships, mines, fleet workshops and lube trucks.\u003c\/p\u003e\u003cp\u003eIt's supplied as the pump only. The RAASM \u003ca href=\"\/products\/8436-252\"\u003e8436.252\u003c\/a\u003e AdBlue reel has a G 3\/4\" female inlet and joins the outlet with a 3\/4\" BSP male nipple. The \u003ca href=\"\/products\/f0040710a\"\u003eF0040710A\u003c\/a\u003e K24 meter logs AdBlue in-line. Graco's matching automatic nozzle is the \u003ca href=\"\/products\/24f529\"\u003e24F529\u003c\/a\u003e.\u003c\/p\u003e\u003cp\u003eGraco requires a bleed-type master air valve (110223), a fluid drain valve and a ground wire and clamp (\u003ca href=\"\/products\/222011\"\u003e222011\u003c\/a\u003e). Because air must stay at or below 3.4 bar, every SD Blue package adds an air safety valve set to that limit (124963 or 116306). Add the \u003ca href=\"\/products\/110147\"\u003e110147\u003c\/a\u003e regulator and \u003ca href=\"\/products\/110146\"\u003e110146\u003c\/a\u003e filter, and mount it on the 24F870 tote or wall bracket or the 24F679 drum bracket. Parts shown without a link are available on request.\u003c\/p\u003e","brand":"Graco","offers":[{"title":"Default Title","offer_id":68172912132175,"sku":"24G745","price":1570.8,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0711\/9110\/1519\/files\/graco-24g745-sd-blue-husky-515-pp-diaphragm-pump.jpg?v=1794952349"}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0711\/9110\/1519\/collections\/AF-AE-KP2115A.jpg?v=1781693193","url":"https:\/\/geelongfiltersales.com.au\/collections\/adblue-pumps.oembed","provider":"Geelong Filter Sales","version":"1.0","type":"link"}