{"title":"Brake Fluids","description":"\u003cp\u003eBrake fluid for hydraulic brake and clutch systems in cars, 4WDs, motorcycles, trucks and performance vehicles. Most brake fluids are glycol-based and rated to US DOT standards, DOT 3, DOT 4 and DOT 5.1, which set minimum boiling points for fresh fluid and for fluid that has absorbed moisture. That moisture is the problem: glycol fluid draws water from the air through hoses and seals over time, lowering its boiling point and corroding components from the inside.\u003c\/p\u003e\u003cp\u003eUse the rating printed on the reservoir cap or in the handbook, and never go below it. Old fluid shows up as a soft pedal and brake fade on a long descent or a hard stop with a load on, which is the worst possible time. The guide below covers ratings and change intervals.\u003c\/p\u003e","products":[{"product_id":"0900-20","title":"0900.20 VPS Super Performance DOT4 Brake Fluid 20L","description":"\u003cp\u003eValvoline VPS Super Performance DOT 4 is a glycol-based brake fluid meeting the DOT 4 standard, supplied in a 20L bulk container for high-volume workshops. Its higher boiling points over DOT 3 resist vapour lock under sustained heavy braking, giving a firmer, more consistent pedal. Bulk supply suits shops that standardise on DOT 4 across the vehicles they service.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eDOT 4 at workshop volume\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eStandardising a busy workshop on DOT 4 makes sense when it services modern vehicles, tow rigs and 4WDs, and buying it in 20L keeps that practical. This glycol DOT 4 fluid carries higher boiling points than DOT 3 to resist vapour lock under sustained heavy braking, giving a firmer, more consistent pedal across the vehicles a shop sees.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhy the higher boiling point matters\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eBrake fluid fails when it boils and turns compressible, and DOT 4 carries more headroom than DOT 3 on both the fresh dry boiling point and the in-service wet boiling point. That is what holds pedal feel when brakes run hot, so standardising a workshop on DOT 4 suits shops servicing modern vehicles, tow rigs and 4WDs.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eBulk value and standards\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eCorrosion inhibitors protect seals, cylinders and metal internals, and it meets DOT 4, SAE J1704, FMVSS 116 and AS\/NZS 1960.1 Grade 3. The 20L pack keeps bays stocked and lowers the cost per vehicle across frequent brake service.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhere it fits\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eIt suits busy workshops and fleets standardising on a DOT 4 brake and clutch fluid. Always confirm the fluid grade a vehicle specifies before service.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eBulk handling and change intervals\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eBuying DOT 4 in 20L suits a high-volume shop, provided the container is kept sealed between uses, since glycol fluid takes up moisture from the air and that lowers the boiling point. Draw off through a clean dispenser or bleeder, and change each vehicle's fluid on the usual couple-of-year schedule to hold the boiling point up and slow corrosion. Keep the fluid clear of paint and never mix in a silicone DOT 5 product. DOT 4 can be used where DOT 3 is specified, but not the other way around. Handled this way, bulk DOT 4 keeps a workshop standardised and stocked economically.\u003c\/p\u003e","brand":"Valvoline","offers":[{"title":"Default Title","offer_id":45478392725583,"sku":"0900.20","price":329.0,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0711\/9110\/1519\/files\/valvoline-0900-20-super-performance-dot4-brake-fluid-20l.webp?v=1785300640"},{"product_id":"0903-20","title":"0903.20 VPS Heavy Duty DOT3 Brake Fluid 20L","description":"\u003cp\u003eValvoline VPS Heavy Duty DOT 3 is a glycol-based brake fluid meeting the DOT 3 standard, supplied in a 20L bulk container for high-volume workshops. It is the standard-service fluid for hydraulic brake and clutch systems that do not require DOT 4, delivering dependable braking and internal corrosion protection. Bulk supply keeps busy service bays stocked and lowers cost per vehicle.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eDOT 3 at workshop volume\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eFor a high-volume workshop, buying brake fluid by the small bottle gets expensive fast. This glycol DOT 3 fluid comes in a 20L container for exactly that reason, delivering dependable braking and internal corrosion protection for systems that do not require DOT 4, while keeping the bays stocked and the cost per vehicle low.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eReliable performance, protected internals\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eA DOT 3 system is designed around a particular boiling performance, and this fluid delivers it consistently for general road service, so the pedal stays firm under normal driving. Its corrosion inhibitors safeguard the rubber seals and metal internals of the master cylinder, callipers and lines against the internal corrosion that shortens hydraulic component life.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eBulk value and standards\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eIt meets DOT 3, SAE J1703, FMVSS 116 and AS\/NZS 1960.1 Grade 1. The 20L pack keeps busy bays stocked and drops the cost per vehicle noticeably across a week of brake work, decanting cleanly into a dispenser or brake bleeder.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhere it fits\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eIt suits automotive workshops and fleet servicing carrying out DOT 3 brake fluid changes at volume. Where a vehicle specifies DOT 4, use a DOT 4 fluid, and confirm the grade before service.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eBulk handling and change intervals\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eA 20L container is efficient for a busy workshop, but it does mean managing moisture: keep the container sealed between uses, since glycol fluid absorbs water from the air, and draw off through a clean dispenser or brake bleeder rather than leaving it open. A scheduled fluid change every couple of years keeps each vehicle's boiling point up and slows corrosion. Keep the fluid off paintwork, and never mix a silicone DOT 5 product into a glycol system. Where a vehicle specifies DOT 4, use DOT 4 rather than DOT 3. Managed this way, bulk supply keeps the bays stocked and the cost per vehicle low.\u003c\/p\u003e","brand":"Valvoline","offers":[{"title":"Default Title","offer_id":45478399443023,"sku":"0903.20","price":239.0,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0711\/9110\/1519\/files\/valvoline-0903-20-heavy-duty-dot3-brake-fluid-20l.webp?v=1785300640"},{"product_id":"0905-72","title":"0905.72 VR1 Racing Brake Fluid 500ml","description":"\u003cp\u003eValvoline VR1 Racing Brake Fluid is a high-boiling glycol fluid built for motorsport and track use, where brakes reach temperatures that boil ordinary road fluid. With a dry boiling point well above the DOT 4 requirement, it holds a firm pedal through repeated heavy braking, lap after lap. The 500ml bottle is sized for a fresh flush before a track day or race meeting.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eA brake fluid built for the track\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eOn a race track or a hard track day, brakes reach temperatures that boil ordinary road fluid, and once the fluid boils the pedal goes long and the car will not pull up. This high-boiling glycol fluid is built for that environment, with a dry boiling point well above the DOT 4 requirement so it holds a firm pedal lap after lap.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhy the boiling point is everything\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eRepeated heavy braking dumps enormous heat into the fluid at the calliper. The extra dry boiling point headroom is what keeps the fluid liquid and incompressible through that heat, so the driver keeps a consistent, predictable pedal when it matters most. Corrosion inhibitors protect the calliper and cylinder internals through the season.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eFor competition use\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eIt clears the DOT 4 requirement with margin and is intended for motorsport, track-day and high-performance use. Because racing fluids are worked hard and absorb moisture over time, a fresh flush before an event keeps the boiling performance where it should be. The 500ml bottle is sized for a pre-event bleed.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhere it fits\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eIt suits competition cars, track-day vehicles and high-performance road cars that punish their brakes, wherever a standard road fluid would fade under sustained hard use.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eGetting the most on track\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eRacing fluid earns its boiling-point advantage only when it is fresh, and because glycol fluid absorbs moisture quickly under hard use, a flush before each event or track day is normal practice rather than an annual habit. Bleed thoroughly to clear any air, since air in the system does the same thing as boiled fluid and gives a long, soft pedal. Use fluid from a sealed bottle, keep it off paint, and do not mix in a silicone DOT 5 product. It remains a glycol DOT 4 fluid, so it is compatible with standard road systems, which makes a pre-event flush and a return to normal service straightforward.\u003c\/p\u003e","brand":"Valvoline","offers":[{"title":"Default Title","offer_id":45478407471183,"sku":"0905.72","price":30.95,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0711\/9110\/1519\/files\/valvoline-0905-72-racing-brake-fluid-500ml.webp?v=1785300641"},{"product_id":"8505","title":"8505 Super Performance DOT4 Brake Fluid 500ml","description":"\u003cp\u003eValvoline Super Performance DOT 4 is a high-boiling glycol brake fluid for hydraulic brake and clutch systems, supplied in a 500ml top-up bottle. Its high dry and wet boiling points give real headroom over DOT 3, resisting the vapour lock and soft pedal that come from fluid boiling under sustained braking. The compact bottle suits bleeding, top-ups and single-vehicle service.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eDOT 4 protection for everyday and harder driving\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eBrake fluid works by being incompressible, so when it boils and forms vapour the pedal goes soft and braking fades. Resisting that failure, vapour lock, is exactly what a higher-specification fluid is for. This high-boiling glycol DOT 4 fluid carries real headroom over DOT 3, holding a firm pedal where an entry-level fluid would start to soften.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhy the higher boiling point matters\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eIts high dry and wet boiling points are the headline. Dry boiling point is the fresh fluid; wet boiling point is after the fluid has absorbed some moisture in service, which glycol fluids always do over time. DOT 4 sits above DOT 3 on both counts, which is what keeps the pedal consistent through repeated heavy braking, towing or long descents.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eProtects the system, meets the standards\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eCorrosion inhibitors protect the seals, cylinders and metal internals of the hydraulic system, and it meets DOT 4, SAE J1704, FMVSS 116 and AS\/NZS 1960.1 Grade 3. The 500ml bottle is sealed and sized for bleeding and top-ups on a single vehicle.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhere it fits\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eIt suits modern cars, 4WDs and light commercials that specify DOT 4, and it is a sensible choice wherever brakes work hard, from towing and hilly driving to fully loaded vehicles. Always confirm the fluid grade your vehicle calls for before topping up.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhy brake fluid needs changing\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eGlycol brake fluids are hygroscopic, meaning they absorb moisture from the air over time, and that moisture lowers the boiling point and promotes internal corrosion. That is why manufacturers specify a fluid change every couple of years regardless of distance, and why an opened bottle is best used promptly rather than stored half-full. Always use fresh fluid from a sealed container for a bleed or top-up, keep it off paintwork as glycol fluid can lift paint, and never mix in a silicone DOT 5 fluid, which is not compatible with glycol systems. Confirming the grade the vehicle specifies and changing on schedule keeps the pedal firm and the hydraulics protected.\u003c\/p\u003e","brand":"Valvoline","offers":[{"title":"Default Title","offer_id":45478947881039,"sku":"8505","price":12.95,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0711\/9110\/1519\/files\/valvoline-8505-super-performance-dot4-brake-fluid-500ml.webp?v=1785300741"},{"product_id":"8508","title":"8508 Heavy Duty DOT3 Brake Fluid 500ml","description":"\u003cp\u003eValvoline Heavy Duty DOT 3 is a premium glycol-ether brake fluid for hydraulic brake and clutch systems that specify a DOT 3 fluid, packaged in a 500ml top-up bottle. Formulated with advanced inhibitors, it delivers reliable boiling performance for everyday braking while protecting rubber components and metal surfaces from corrosion.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eA dependable DOT 3 for general service\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eA DOT 3 system is designed around a particular boiling performance, and this premium glycol-ether fluid is formulated with advanced inhibitors to deliver it reliably for everyday braking. Just as importantly, it protects the rubber and metal it runs through, guarding the master cylinder, callipers and lines against internal corrosion.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eConsistent braking, protected internals\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eBrake fluid has to stay incompressible to give a firm pedal, which means resisting the heat that braking generates. This fluid delivers the stable boiling performance a DOT 3 system is designed around, so the pedal stays consistent under normal road driving. Its corrosion inhibitors protect the rubber seals and metal surfaces inside the master cylinder, callipers and lines, guarding against the internal corrosion that shortens the life of hydraulic components.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eMeets the standards\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eIt meets DOT 3, SAE J1703, FMVSS 116 and AS\/NZS 1960.1 Grade 1, the specifications a DOT 3 brake and clutch system calls for. The 500ml bottle is sealed and sized for bleeding and top-ups on a single vehicle.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhere it fits\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eIt suits passenger cars and light vehicles that specify a DOT 3 brake and clutch fluid. Where a vehicle calls for the higher boiling points of DOT 4, use a DOT 4 fluid instead, and always confirm the required grade before topping up.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhy brake fluid needs changing\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eBeing hygroscopic, DOT 3 fluid absorbs moisture from the atmosphere over time, which lowers its boiling point and encourages corrosion inside the master cylinder, callipers and lines. Manufacturers therefore call for a periodic fluid change, typically every two years, independent of how far the vehicle has travelled. Use fresh fluid from a sealed bottle when bleeding or topping up, avoid contact with paintwork, and do not mix a silicone DOT 5 fluid into a glycol system. Where a vehicle specifies DOT 4, fit DOT 4 rather than stepping down to DOT 3. Sticking to the correct grade and change interval is what keeps braking consistent and the hydraulic system sound.\u003c\/p\u003e","brand":"Valvoline","offers":[{"title":"Default Title","offer_id":45478955384911,"sku":"8508","price":12.95,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0711\/9110\/1519\/files\/valvoline-8508-heavy-duty-dot3-brake-fluid-500ml.webp?v=1785300742"},{"product_id":"0971-88","title":"0971.88 Clear DOT3 Brake Fluid 2.5L","description":"\u003cp\u003eValvoline Clear DOT 3 is a glycol-based brake fluid meeting the DOT 3 standard, supplied in a 2.5L pack for workshops. As the standard-service fluid for hydraulic brake and clutch systems that do not require the higher boiling points of DOT 4, it delivers consistent braking and protects the system against internal corrosion. The clear colour makes it easy to judge fluid condition during a flush.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eStandard-service DOT 3 in a workshop pack\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eFor hydraulic brake and clutch systems that do not need the higher boiling points of DOT 4, this glycol DOT 3 fluid is the standard-service choice, delivering consistent braking and internal corrosion protection. Its clear colour is a practical bonus: when clean fluid runs at the bleeder, the colour change tells you the old fluid has been fully flushed through.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhy the clear colour helps\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eFresh brake fluid is light in colour and darkens as it ages and absorbs moisture. Because this fluid is clear, it makes a flush easier to judge: when clean fluid runs at the bleeder, the colour change tells you the old fluid has been pushed through. That is a practical advantage when you are working through several vehicles.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eProtection and standards\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eCorrosion inhibitors protect the seals, cylinders and metal internals of the hydraulic system, and it meets DOT 3, SAE J1703, FMVSS 116 and AS\/NZS 1960.1 Grade 1. The 2.5L pack holds enough for full fluid changes across multiple vehicles.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhere it fits\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eIt suits workshops carrying out brake fluid changes on cars and light commercials that specify DOT 3. Where a vehicle requires DOT 4, use a DOT 4 fluid, and confirm the required grade before service.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eFlushing and change intervals\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eBecause glycol fluid absorbs moisture over time, a scheduled flush every couple of years keeps the boiling point up and slows internal corrosion, which matters as much as topping up a low reservoir. The clear colour is a practical help here: keep bleeding at each wheel until clean, fresh-coloured fluid runs through, and you can see the old fluid has been fully replaced. Use fluid from a sealed container, keep it off paint, and never introduce a silicone DOT 5 product into a glycol system. For any vehicle that calls for DOT 4, use a DOT 4 fluid instead, and always confirm the specification before starting the job.\u003c\/p\u003e","brand":"Valvoline","offers":[{"title":"Default Title","offer_id":45479935770703,"sku":"0971.88","price":53.9,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0711\/9110\/1519\/files\/valvoline-0971-88-clear-dot3-brake-fluid-2-5l.webp?v=1785301052"},{"product_id":"0970-88","title":"0970.88 Clear Super Performance DOT4 Brake Fluid 2.5L","description":"\u003cp\u003eValvoline Clear Super Performance DOT 4 is a glycol-based brake fluid meeting the DOT 4 standard, supplied in a 2.5L workshop pack. Its higher dry and wet boiling points over DOT 3 resist vapour lock, the soft pedal that appears when fluid boils under hard, repeated braking. The clear-to-amber colour helps confirm clean fluid during a system flush.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eDOT 4 headroom in a workshop pack\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eHigher dry and wet boiling points are what a DOT 4 fluid brings over DOT 3, and they are what resist vapour lock, the soft pedal that appears when brake fluid boils under hard, repeated braking. This glycol DOT 4 fluid carries that headroom, and its clear-to-amber colour makes a system flush easy to judge at the bleeder.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhy the higher boiling point matters\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eBrake fluid must stay incompressible to give a firm pedal, and it fails by boiling. DOT 4 sits above DOT 3 on both the fresh dry boiling point and the in-service wet boiling point, which is what holds pedal feel through sustained heavy braking, towing and long descents. The clear-to-amber colour also makes a flush easy to judge, since clean fluid at the bleeder confirms the old fluid has been pushed through.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eProtection and standards\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eCorrosion inhibitors protect seals, cylinders and metal internals, and it meets DOT 4, SAE J1704, FMVSS 116 and AS\/NZS 1960.1 Grade 3. The 2.5L pack suits full fluid changes across multiple vehicles.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhere it fits\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eIt suits workshops servicing modern vehicles, 4WDs and tow vehicles that specify DOT 4. Always confirm the fluid grade the vehicle calls for before service.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eFlushing and change intervals\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eDOT 4 fluid absorbs moisture over time like all glycol fluids, so a flush every couple of years keeps the boiling point high and holds off internal corrosion. When bleeding, work through each wheel until clean fluid of the fresh colour runs at the bleeder, confirming the old fluid is gone. Always use fluid from a sealed container, since an opened bottle takes up moisture, keep it clear of paintwork, and never mix in a silicone DOT 5 product. DOT 4 can be used where DOT 3 is specified for extra boiling headroom, but do not step down from a DOT 4 requirement to DOT 3.\u003c\/p\u003e","brand":"Valvoline","offers":[{"title":"Default Title","offer_id":45479963230287,"sku":"0970.88","price":55.9,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0711\/9110\/1519\/files\/valvoline-0970-88-clear-dot4-brake-fluid-2-5l.webp?v=1785301051"}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0711\/9110\/1519\/collections\/Brake-Fluid_Category-Image.webp?v=1781693292","url":"https:\/\/geelongfiltersales.com.au\/collections\/brake-fluids.oembed","provider":"Geelong Filter Sales","version":"1.0","type":"link"}