{"title":"Grease","description":"\u003cp\u003eGrease for wheel bearings, chassis points, pins, bushes, slewing rings and plant bearings on vehicles, trucks, farm machinery and earthmoving gear. A grease is base oil held in a thickener. The thickener sets water resistance and the temperature the grease can handle, the base oil viscosity sets load-carrying ability, and additives such as EP agents or moly add protection for heavy, slow-moving joints.\u003c\/p\u003e\u003cp\u003eThe NLGI grade describes consistency, with NLGI 2 the most common for general greasing and softer grades used in centralised lube systems. Pick the wrong grease and it runs out of a hot wheel bearing, washes off a pin in the wet or gets squeezed out of a loaded joint, leaving it dry. The notes below explain thickeners and grades.\u003c\/p\u003e","products":[{"product_id":"0706-67","title":"0706.67 Valplex M All Purpose Grease, Lithium Complex with 3% Moly 2.5kg","description":"\u003cp\u003eValvoline Valplex M is an NLGI 2 all-purpose grease on a lithium complex thickener with 3% molybdenum disulphide (moly). The high dropping point keeps it in place on hot joints and bearings, while the moly builds a solid film at sliding, shock-loaded points that an oil film cannot hold. The 2.5kg tub is a practical size for hand-greasing and regular workshop use.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eA moly grease for sliding, shock-loaded points\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eOn sliding, shock-loaded points an ordinary grease gets squeezed out and metal starts working against metal, which is exactly the problem a moly grease solves. Built on a lithium complex thickener and fortified with 3% molybdenum disulphide, this NLGI 2 grease is designed for the pins, bushes and joints on trucks, trailers and earthmoving gear that take a beating.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhy the thickener and the moly matter\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe lithium complex base gives the grease a high dropping point, so it stays in place in joints and bearings that build heat under load rather than running out. The moly adds a second line of defence: a solid, sacrificial film that keeps protecting at the exact moment an oil film is crushed out, such as the reversing, high-pressure contact in a pin and bush. Together they handle shock loads and sliding friction that would defeat a standard grease.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eStays put and resists water\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eIt is tacky and adhesive so it clings instead of flinging off, carries extreme-pressure additives for heavy load, and includes rust and oxidation inhibitors for greased points exposed to moisture and weather.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eValplex M or a moly-free grease\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eChoose Valplex M for sliding and shock-loaded points such as king pins, spring pins and bushes, ball and CV joints, fifth wheels and chassis points. For high-speed rolling-element bearings such as wheel bearings and pulleys, a moly-free extreme-pressure grease is the better call, since moly is formulated for sliding rather than rolling contact.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eRelubrication and compatibility\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eGrease intervals depend on the point, the load and the environment, so follow the equipment maker's schedule and grease more often on wet, dusty or heavily loaded points, purging fresh grease through until clean grease appears. Take care when switching greases: mixing incompatible thickener types can break a grease down, and while lithium complex greases are broadly compatible with many others, it is best to purge the old grease through when changing types. Because Valplex M contains moly, keep it to the sliding, shock-loaded points it is designed for. Clean the fitting before greasing so grit is not driven into the bearing, which is a common and avoidable cause of wear.\u003c\/p\u003e","brand":"Valvoline","offers":[{"title":"Default Title","offer_id":45478355501135,"sku":"0706.67","price":71.8,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0711\/9110\/1519\/files\/valvoline-0706-67-valplex-m-3moly-grease-2-5kg.webp?v=1785300634"},{"product_id":"0706-65","title":"0706.65 Valplex M All Purpose Grease, Lithium Complex with 3% Moly 20kg","description":"\u003cp\u003eValvoline Valplex M is an NLGI 2 all-purpose grease on a lithium complex thickener with 3% molybdenum disulphide (moly). The lithium complex base carries a high dropping point so it stays in place in hot joints and bearings, while the moly adds a solid film that keeps protecting sliding, shock-loaded points where an oil film gets squeezed out. The 20kg keg suits fleets and pump-fed greasing.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eA moly grease for sliding, shock-loaded points\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eOn sliding, shock-loaded points an ordinary grease gets squeezed out and metal starts working against metal, which is exactly the problem a moly grease solves. Built on a lithium complex thickener and fortified with 3% molybdenum disulphide, this NLGI 2 grease is designed for the pins, bushes and joints on trucks, trailers and earthmoving gear that take a beating.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhy the thickener and the moly matter\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe lithium complex base gives the grease a high dropping point, so it stays in place in joints and bearings that build heat under load rather than running out. The moly adds a second line of defence: a solid, sacrificial film that keeps protecting at the exact moment an oil film is crushed out, such as the reversing, high-pressure contact in a pin and bush. Together they handle shock loads and sliding friction that would defeat a standard grease.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eStays put and resists water\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eIt is tacky and adhesive so it clings instead of flinging off, carries extreme-pressure additives for heavy load, and includes rust and oxidation inhibitors for greased points exposed to moisture and weather.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eValplex M or a moly-free grease\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eChoose Valplex M for sliding and shock-loaded points such as king pins, spring pins and bushes, ball and CV joints, fifth wheels and chassis points. For high-speed rolling-element bearings such as wheel bearings and pulleys, a moly-free extreme-pressure grease is the better call, since moly is formulated for sliding rather than rolling contact.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eRelubrication and compatibility\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eGrease intervals depend on the point, the load and the environment, so follow the equipment maker's schedule and grease more often on wet, dusty or heavily loaded points, purging fresh grease through until clean grease appears. Take care when switching greases: mixing incompatible thickener types can break a grease down, and while lithium complex greases are broadly compatible with many others, it is best to purge the old grease through when changing types. Because Valplex M contains moly, keep it to the sliding, shock-loaded points it is designed for. Clean the fitting before greasing so grit is not driven into the bearing, which is a common and avoidable cause of wear.\u003c\/p\u003e","brand":"Valvoline","offers":[{"title":"Default Title","offer_id":45478366117967,"sku":"0706.65","price":420.85,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0711\/9110\/1519\/files\/valvoline-0706-65-valplex-m-3moly-grease-20kg.webp?v=1785300634"},{"product_id":"0707-67","title":"0707.67 Valplex EP2 Grease, Extreme Pressure Lithium Complex 2.5kg","description":"\u003cp\u003eValvoline Valplex EP2 is an NLGI 2 lithium complex grease with a non-lead extreme pressure (EP) additive and oxidation and rust inhibitors. It carries NLGI service category GC-LB, for wheel bearings and chassis points. The 2.5kg tub suits hand-packing bearings and regular workshop greasing.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhere it fits\u003c\/strong\u003e\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eVehicles:\u003c\/strong\u003e chassis points on extended lubrication intervals, and wheel bearings with drum or disc brakes, in passenger cars, trucks, farm and earthmoving equipment. Valvoline particularly recommends it for fifth wheels.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eHeavy equipment:\u003c\/strong\u003e excellent wear protection on oscillating bucket pins and universal joints.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eIndustrial:\u003c\/strong\u003e ball and roller bearings, and slow speed, heavily loaded plain bearings, under all service conditions.\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003e\u003cstrong\u003eWhy it holds up\u003c\/strong\u003e\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eDropping point above 260°C, with a smooth, tacky structure and excellent adhesion.\u003c\/li\u003e\n\u003cli\u003eAnti-wear and EP additives for heavy and shock loading: Timken OK load 23 kg, four ball weld point 315.\u003c\/li\u003e\n\u003cli\u003eWater resistant in high moisture conditions: under 10% loss in the ASTM D1264 water washout test at 79°C, and passes the ASTM D1743 rust test.\u003c\/li\u003e\n\u003cli\u003eBase oil viscosity 200 cSt at 40°C.\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003e\u003cstrong\u003eDon't mix greases\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eValvoline says not to mix greases. Wash bearings out before repacking, and repack to the equipment maker's recommended practice. Check the owner's manual before use.\u003c\/p\u003e","brand":"Valvoline","offers":[{"title":"Default Title","offer_id":45478372343887,"sku":"0707.67","price":68.8,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0711\/9110\/1519\/files\/valvoline-0707-67-valplex-ep2-grease.jpg?v=1793486720"},{"product_id":"0707-82","title":"0707.82 Valplex EP2 Grease, Extreme Pressure Lithium Complex 450g","description":"\u003cp\u003eValvoline Valplex EP2 is an NLGI 2 lithium complex grease with a non-lead extreme pressure (EP) additive and oxidation and rust inhibitors. It carries NLGI service category GC-LB, for wheel bearings and chassis points. The 450g cartridge fits a standard grease gun.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhere it fits\u003c\/strong\u003e\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eVehicles:\u003c\/strong\u003e chassis points on extended lubrication intervals, and wheel bearings with drum or disc brakes, in passenger cars, trucks, farm and earthmoving equipment. Valvoline particularly recommends it for fifth wheels.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eHeavy equipment:\u003c\/strong\u003e excellent wear protection on oscillating bucket pins and universal joints.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eIndustrial:\u003c\/strong\u003e ball and roller bearings, and slow speed, heavily loaded plain bearings, under all service conditions.\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003e\u003cstrong\u003eWhy it holds up\u003c\/strong\u003e\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eDropping point above 260°C, with a smooth, tacky structure and excellent adhesion.\u003c\/li\u003e\n\u003cli\u003eAnti-wear and EP additives for heavy and shock loading: Timken OK load 23 kg, four ball weld point 315.\u003c\/li\u003e\n\u003cli\u003eWater resistant in high moisture conditions: under 10% loss in the ASTM D1264 water washout test at 79°C, and passes the ASTM D1743 rust test.\u003c\/li\u003e\n\u003cli\u003eBase oil viscosity 200 cSt at 40°C.\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003e\u003cstrong\u003eDon't mix greases\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eValvoline says not to mix greases. Wash bearings out before repacking, and repack to the equipment maker's recommended practice. Check the owner's manual before use.\u003c\/p\u003e","brand":"Valvoline","offers":[{"title":"Default Title","offer_id":67808890716239,"sku":"0707.82","price":14.6,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0711\/9110\/1519\/files\/valvoline-0707-82-valplex-ep-extreme-pressure-grease-450g.webp?v=1785300637"},{"product_id":"0770-65","title":"0770.65 Optimum Choice Partial Synthetic, Lithium Complex Grease, High Temperature, Severe Service 20kg","description":"\u003cp\u003eValvoline Optimum Choice is a partial-synthetic NLGI 2 lithium complex grease for high-temperature, severe-service greasing. Its synthetic base oil holds viscosity across a wider temperature range than a straight mineral grease, while high-molecular-weight polymers make it cling and resist squeeze-out under heavy load. The 20kg keg is built for fleets and high-usage sites feeding automatic or bulk grease pumps.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eA partial-synthetic grease for severe service\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eSome bearings run too hot and too heavily loaded for a general-purpose grease, which softens or is squeezed out. A partial-synthetic NLGI 2 lithium complex grease is built for exactly those conditions: the synthetic base oil holds viscosity across a wider temperature range and resists oxidation, staying serviceable longer at temperature.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eBuilt to stay put under load\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eHigh-molecular-weight polymers make it cling and resist squeeze-out under heavy load, so it stays where it is needed rather than being forced out of the contact. That, combined with strong extreme-pressure performance, is what suits it to heavily loaded, hot-running bearings that a general-purpose grease cannot keep up with.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eHigh-temperature strength\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe lithium complex thickener gives a high dropping point, and the grease carries the water resistance, rust protection and load-carrying capacity needed for severe outdoor service.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhere it fits\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eIt suits earthmoving, transport and industrial plant greasing heavily loaded, hot bearings and pins, particularly where a standard grease softens or is squeezed out. Match the grease to the operating temperature and load of the point for the intended service life.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eMatching the grease to the service\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eOptimum Choice is a severe-service grease, so it earns its cost on the hot, heavily loaded, hard-to-reach points where a general-purpose grease softens or is squeezed out, rather than on light everyday points. Follow the equipment maker's greasing schedule, purge until clean grease appears, and grease more often on wet or heavily loaded points. When switching greases, purge the old product through, since mixing incompatible thickeners can degrade the grease, and wipe fittings clean before greasing so grit is not driven in. On the demanding bearings and pins it is designed for, the synthetic base oil and adhesive polymer structure keep it working where lesser greases give up.\u003c\/p\u003e","brand":"Valvoline","offers":[{"title":"Default Title","offer_id":45478382829647,"sku":"0770.65","price":450.0,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0711\/9110\/1519\/files\/valvoline-0770-65-optimum-choice-partial-synthetic-lithium-complex.jpg?v=1793486720"},{"product_id":"0770-82","title":"0770.82 Optimum Choice Partial Synthetic, Lithium Complex Grease, High Temperature, Severe Service 450g","description":"\u003cp\u003eValvoline Optimum Choice is a partial-synthetic NLGI 2 lithium complex grease for high-temperature, severe-service applications. The synthetic base oil holds viscosity across a wide temperature range and its adhesive polymer structure resists squeeze-out under heavy load. The 450g cartridge fits a standard grease gun, making it the convenient choice for chassis points and bearings in the field or workshop.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eA partial-synthetic grease for severe service\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eSome bearings run too hot and too heavily loaded for a general-purpose grease, which softens or is squeezed out. A partial-synthetic NLGI 2 lithium complex grease is built for exactly those conditions: the synthetic base oil holds viscosity across a wider temperature range and resists oxidation, staying serviceable longer at temperature.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eBuilt to stay put under load\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eHigh-molecular-weight polymers make it cling and resist squeeze-out under heavy load, so it stays where it is needed rather than being forced out of the contact. That, combined with strong extreme-pressure performance, is what suits it to heavily loaded, hot-running bearings that a general-purpose grease cannot keep up with.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eHigh-temperature strength\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe lithium complex thickener gives a high dropping point, and the grease carries the water resistance, rust protection and load-carrying capacity needed for severe outdoor service.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhere it fits\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eIt suits earthmoving, transport and industrial plant greasing heavily loaded, hot bearings and pins, particularly where a standard grease softens or is squeezed out. Match the grease to the operating temperature and load of the point for the intended service life.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eMatching the grease to the service\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eOptimum Choice is a severe-service grease, so it earns its cost on the hot, heavily loaded, hard-to-reach points where a general-purpose grease softens or is squeezed out, rather than on light everyday points. Follow the equipment maker's greasing schedule, purge until clean grease appears, and grease more often on wet or heavily loaded points. When switching greases, purge the old product through, since mixing incompatible thickeners can degrade the grease, and wipe fittings clean before greasing so grit is not driven in. On the demanding bearings and pins it is designed for, the synthetic base oil and adhesive polymer structure keep it working where lesser greases give up.\u003c\/p\u003e","brand":"Valvoline","offers":[{"title":"Default Title","offer_id":45478389973071,"sku":"0770.82","price":17.6,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0711\/9110\/1519\/files\/valvoline-0770-82-optimum-choice-partial-synthetic-grease-450g.webp?v=1785300639"},{"product_id":"0706-82","title":"0706.82 Valplex M All Purpose Grease, Lithium Complex with 3% Moly 450g","description":"\u003cp\u003eValvoline Valplex M is an NLGI 2 all-purpose grease on a lithium complex thickener with 3% molybdenum disulphide (moly). The high dropping point holds it in place on hot joints, while the moly adds a solid film for sliding, shock-loaded points. The 450g cartridge fits a standard grease gun, making it ideal for chassis and joint greasing in the field or on the hoist.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eA moly grease for sliding, shock-loaded points\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eOn sliding, shock-loaded points an ordinary grease gets squeezed out and metal starts working against metal, which is exactly the problem a moly grease solves. Built on a lithium complex thickener and fortified with 3% molybdenum disulphide, this NLGI 2 grease is designed for the pins, bushes and joints on trucks, trailers and earthmoving gear that take a beating.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhy the thickener and the moly matter\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe lithium complex base gives the grease a high dropping point, so it stays in place in joints and bearings that build heat under load rather than running out. The moly adds a second line of defence: a solid, sacrificial film that keeps protecting at the exact moment an oil film is crushed out, such as the reversing, high-pressure contact in a pin and bush. Together they handle shock loads and sliding friction that would defeat a standard grease.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eStays put and resists water\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eIt is tacky and adhesive so it clings instead of flinging off, carries extreme-pressure additives for heavy load, and includes rust and oxidation inhibitors for greased points exposed to moisture and weather.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eValplex M or a moly-free grease\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eChoose Valplex M for sliding and shock-loaded points such as king pins, spring pins and bushes, ball and CV joints, fifth wheels and chassis points. For high-speed rolling-element bearings such as wheel bearings and pulleys, a moly-free extreme-pressure grease is the better call, since moly is formulated for sliding rather than rolling contact.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eRelubrication and compatibility\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eGrease intervals depend on the point, the load and the environment, so follow the equipment maker's schedule and grease more often on wet, dusty or heavily loaded points, purging fresh grease through until clean grease appears. Take care when switching greases: mixing incompatible thickener types can break a grease down, and while lithium complex greases are broadly compatible with many others, it is best to purge the old grease through when changing types. Because Valplex M contains moly, keep it to the sliding, shock-loaded points it is designed for. Clean the fitting before greasing so grit is not driven into the bearing, which is a common and avoidable cause of wear.\u003c\/p\u003e","brand":"Valvoline","offers":[{"title":"Default Title","offer_id":67808160972879,"sku":"0706.82","price":15.6,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0711\/9110\/1519\/files\/valvoline-0706-82-valplex-m-3moly-grease-450g.jpg?v=1792451323"},{"product_id":"0707-65","title":"0707.65 Valplex EP2 Grease, Extreme Pressure Lithium Complex 20kg","description":"\u003cp\u003eValvoline Valplex EP2 is an NLGI 2 lithium complex grease with a non-lead extreme pressure (EP) additive and oxidation and rust inhibitors. It carries NLGI service category GC-LB, for wheel bearings and chassis points. The 20kg pail suits fleets and sites running a bucket or air operated grease pump.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhere it fits\u003c\/strong\u003e\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eVehicles:\u003c\/strong\u003e chassis points on extended lubrication intervals, and wheel bearings with drum or disc brakes, in passenger cars, trucks, farm and earthmoving equipment. Valvoline particularly recommends it for fifth wheels.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eHeavy equipment:\u003c\/strong\u003e excellent wear protection on oscillating bucket pins and universal joints.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eIndustrial:\u003c\/strong\u003e ball and roller bearings, and slow speed, heavily loaded plain bearings, under all service conditions.\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003e\u003cstrong\u003eWhy it holds up\u003c\/strong\u003e\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eDropping point above 260°C, with a smooth, tacky structure and excellent adhesion.\u003c\/li\u003e\n\u003cli\u003eAnti-wear and EP additives for heavy and shock loading: Timken OK load 23 kg, four ball weld point 315.\u003c\/li\u003e\n\u003cli\u003eWater resistant in high moisture conditions: under 10% loss in the ASTM D1264 water washout test at 79°C, and passes the ASTM D1743 rust test.\u003c\/li\u003e\n\u003cli\u003eBase oil viscosity 200 cSt at 40°C.\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003e\u003cstrong\u003eDon't mix greases\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eValvoline says not to mix greases. Wash bearings out before repacking, and repack to the equipment maker's recommended practice. Check the owner's manual before use.\u003c\/p\u003e","brand":"Valvoline","offers":[{"title":"Default Title","offer_id":45479133216847,"sku":"0707.65","price":389.0,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0711\/9110\/1519\/files\/valvoline-0707-65-valplex-ep-extreme-pressure-grease-20kg.webp?v=1785300636"},{"product_id":"0749-67","title":"0749.67 Wheel Bearing Grease, Bentone Inorganic Thickener, High Temperature, No Melt 2.5kg","description":"\u003cp\u003eValvoline Wheel Bearing Grease uses a bentone (clay) inorganic thickener with no dropping point, so it softens under heat rather than melting out of the bearing the way a soap-thickened grease can. Valvoline rates it satisfactory up to 180°C. Supplied in a 2.5kg tub for hand-packing bearings.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhere it fits\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eUse it for passenger car and light vehicle wheel bearings, particularly behind disc brakes, and for bearings in equipment that runs hot.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eNot for truck or semi-trailer wheel bearings\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eValvoline does not recommend it for truck or semi-trailer wheel bearings. Use \u003ca href=\"\/products\/0707-82\"\u003eValplex EP2\u003c\/a\u003e, which carries NLGI service category GC-LB and is listed for truck wheel bearings and fifth wheels.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eDon't mix greases\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eClay and soap thickeners are different chemistry, and Valvoline says not to mix greases. Wash the old grease out of the bearing before repacking with this grease, and again if you switch back. Hand-pack the grease fully into the rollers and cage, and set the bearing preload to the vehicle maker's specification on reassembly.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eTypical properties\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eNLGI 2, amber, smooth and buttery, worked penetration 260 to 290, no dropping point, base oil 500 cSt at 40°C.\u003c\/p\u003e","brand":"Valvoline","offers":[{"title":"Default Title","offer_id":45479134855247,"sku":"0749.67","price":68.8,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0711\/9110\/1519\/files\/valvoline-0749-67-wheel-bearing-grease-2-5kg.jpg?v=1793486758"}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0711\/9110\/1519\/collections\/Grease_Category-Image.webp?v=1794565986","url":"https:\/\/geelongfiltersales.com.au\/collections\/grease.oembed","provider":"Geelong Filter Sales","version":"1.0","type":"link"}