{"title":"Compressor, Slideway \u0026 Industrial Gear Oils","description":"\u003cp\u003eCompressor, chain and industrial gear oils for fixed plant, workshops, factories, sawmills and forestry gear. Each type does a specific job. Industrial gear oils carry extreme-pressure additives for enclosed gearboxes under shock load. Compressor oils resist oxidation and carbon at high discharge temperatures. Chain and bar oils cling to fast-moving chains.\u003c\/p\u003e\u003cp\u003eChoose the oil type the equipment maker names, then the ISO viscosity grade on the nameplate or in the manual. These oils aren't interchangeable. An engine or hydraulic oil in a compressor can carbon up and run hot, and too light a grade in an enclosed gearbox lets the gear teeth pit. The notes below cover the standards to look for.\u003c\/p\u003e","products":[{"product_id":"1233-20","title":"1233.20 EPG Industrial Gear Oil 220 20L","description":"\u003cp\u003eValvoline EPG Industrial Gear Oil 220 is an ISO 220 mineral gear oil with sulphur-phosphorus extreme pressure additives, built for heavily loaded enclosed gearboxes that need a heavier film than an ISO 150. It delivers strong load-carrying capacity while resisting oxidation, foaming and corrosion for dependable, long-interval service. The 20L pack suits individual gearbox changes and plant maintenance.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eA heavier grade for higher-load drives\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eSlower, more heavily loaded gears need a thicker oil to keep the teeth separated under pressure, which is where an ISO 220 grade earns its place over a lighter ISO 150. This mineral oil pairs that heavier film with sulphur-phosphorus extreme pressure (EP) additives, delivering strong load-carrying capacity for demanding enclosed gearboxes.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eHow the EP additives work\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eWhen load squeezes the film thin, the sulphur-phosphorus additives react at the contact points to form a protective layer that carries the pressure and prevents scuffing and welding of the gear faces. Combined with the ISO 220 film thickness, that gives strong protection for demanding, high-torque drives.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eClean, long service life\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe oil resists oxidation, foaming and corrosion so it stays serviceable through long intervals and keeps the gearbox internals protected. It meets AGMA 9005-EO2, DIN 51517 Part 3 and US Steel 224.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhere it fits\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eIt suits heavily loaded enclosed gearboxes in manufacturing and materials-handling equipment. Matching the ISO grade to the gearbox maker's recommendation is what delivers the intended life, so a lighter or heavier grade may suit faster or slower drives respectively.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eSelecting and maintaining the oil\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eAn ISO 220 grade suits heavier-loaded or slower drives, but the right choice is always the gearbox maker's specified viscosity, since a mismatched grade either runs hot or leaves the film too thin under load. Keep the oil clean and topped to level, guard against water ingress in wet environments, and change at the recommended interval or when analysis indicates. Draining the gearbox warm removes more of the old, contaminated oil and lets the fresh charge work as intended. Getting the viscosity and cleanliness right is what allows the extreme-pressure additives to protect the gears through the long, heavy duty cycles these drives run.\u003c\/p\u003e","brand":"Valvoline","offers":[{"title":"Default Title","offer_id":45478999556175,"sku":"1233.20","price":229.0,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0711\/9110\/1519\/files\/valvoline-1233-20-epg-industrial-gear-oil-220-20l.webp?v=1785300677"},{"product_id":"1234-20","title":"1234.20 EPG Industrial Gear Oil 320 20L","description":"\u003cp\u003eValvoline EPG Industrial Gear Oil 320 is an ISO 320 mineral gear oil with sulphur-phosphorus extreme pressure additives, formulated for the most heavily loaded, slow-speed enclosed gearboxes. Its thick, tenacious film maximises load-carrying capacity and resists squeeze-out, while oxidation and foam resistance keep the oil serviceable through long drains. Supplied in a 20L pack.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eMaximum film strength for the heaviest drives\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe heaviest, slowest-turning gearboxes squeeze a lighter oil straight out of the contact zone, so they call for the thickest, most tenacious film. This ISO 320 mineral oil, fortified with sulphur-phosphorus extreme pressure (EP) additives, is formulated for exactly those high-torque, low-speed drives, maximising the film that stays in place under heavy, slow loading.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eHow the EP additives work\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eAt the tooth contact, the sulphur-phosphorus additives react under pressure to build a protective layer that carries extreme load and resists the scuffing and welding that would otherwise wreck the gear faces. The ISO 320 viscosity maximises the film that stays in place under heavy, slow loading.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eClean, long service life\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe formulation resists oxidation, foaming and corrosion so the oil holds up through long drains and keeps the gearbox clean and protected. It meets AGMA 9005-EO2, DIN 51517 Part 3 and US Steel 224.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhere it fits\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eIt suits high-torque, low-speed industrial gearboxes in heavy manufacturing and mineral processing. Selecting to the gearbox maker's viscosity recommendation is important, since an over- or under-specified grade will not protect a heavily loaded drive as intended.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eSelecting and maintaining the oil\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eAn ISO 320 grade is chosen for the heaviest, slowest drives, but always confirm it against the gearbox maker's recommendation, since these high-torque boxes are designed around a particular viscosity and film thickness. Keep the oil clean and at level, protect it from water ingress, and change at the specified interval or when oil analysis calls for it. Because these drives run slow and hot, draining warm to carry out contamination and refilling with a clean charge matters for service life. With the correct viscosity and clean oil, the extreme-pressure additives can do their job of protecting the gear faces under the shock and load these applications generate.\u003c\/p\u003e","brand":"Valvoline","offers":[{"title":"Default Title","offer_id":45479009222735,"sku":"1234.20","price":229.0,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0711\/9110\/1519\/files\/valvoline-1234-20-epg-industrial-gear-oil-320-20l.webp?v=1785300678"},{"product_id":"2036-20","title":"2036.20 Valcomp 46 Compressor Oil 20L","description":"\u003cp\u003eValvoline Valcomp 46 is an ISO 46 compressor oil formulated for rotary and reciprocating air compressors. Its advanced additive system delivers strong antioxidant, anti-corrosion and anti-foam performance, controlling carbon and varnish so valves and vanes stay clean and the compressor runs cool and efficient. The 20L pack suits workshops and single-machine servicing.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003ePurpose-built for air compressors\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eAn air compressor is a hard place for an oil: it runs hot, works the oil against oxygen constantly, and any breakdown shows up as carbon and varnish on the valves and vanes. This ISO 46 compressor oil is built specifically to resist that, with an additive system that keeps the air end clean and the compressor running cool and efficient.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eHow it protects the compressor\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eIts advanced additive system delivers strong antioxidant, anti-corrosion and anti-foam performance. The antioxidants slow the oxidation that forms deposits at high temperature, so valves, vanes and the air end stay clean and the compressor keeps running cool and efficient. Anti-foam control keeps the oil delivering a consistent film, and corrosion inhibitors protect the internals.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eClean running, longer oil life\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eBy keeping deposits down and resisting oxidation, the oil holds its condition longer, which supports reliable air delivery and sensible service intervals. It meets DIN 51506 VD-L, a recognised air-compressor lubricant classification.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhere it fits\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eIt suits industrial and mobile air compressors in workshops, farms and manufacturing, both rotary screw and reciprocating types. Running an oil formulated for compressor duty, rather than a general industrial oil, is what keeps carbon and varnish off the valves and vanes over the long term.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eService and oil life\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eCompressor oil works hardest at high temperature, so keeping the compressor cooling clean and the oil at the right level helps it reach its full service life. Change the oil at the maker's recommended hours, or sooner in dusty or hot conditions, and replace or clean the air intake filter on schedule so grit does not shorten the oil's life or wear the air end. When changing, drain warm to carry out more of the old oil and any moisture, and confirm the ISO grade matches the compressor's requirement. Clean oil, changed on time, is what keeps valves and vanes free of the carbon and varnish that rob a compressor of efficiency.\u003c\/p\u003e","brand":"Valvoline","offers":[{"title":"Default Title","offer_id":45479051984975,"sku":"2036.20","price":229.0,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0711\/9110\/1519\/files\/valvoline-2036-20-valcomp-46-compressor-oil-20l.webp?v=1785300720"},{"product_id":"2036-51","title":"2036.51 Valcomp 46 Compressor Oil 205L","description":"\u003cp\u003eValvoline Valcomp 46 is an ISO 46 compressor oil for rotary and reciprocating air compressors, with an additive package built to resist oxidation, corrosion and foam. It keeps valves and vanes free of carbon and varnish so compressors deliver clean, efficient air with reliable oil life. The 205L drum is the bulk choice for operations running several compressors.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003ePurpose-built for air compressors\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eAn air compressor is a hard place for an oil: it runs hot, works the oil against oxygen constantly, and any breakdown shows up as carbon and varnish on the valves and vanes. This ISO 46 compressor oil is built specifically to resist that, with an additive system that keeps the air end clean and the compressor running cool and efficient.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eHow it protects the compressor\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eIts advanced additive system delivers strong antioxidant, anti-corrosion and anti-foam performance. The antioxidants slow the oxidation that forms deposits at high temperature, so valves, vanes and the air end stay clean and the compressor keeps running cool and efficient. Anti-foam control keeps the oil delivering a consistent film, and corrosion inhibitors protect the internals.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eClean running, longer oil life\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eBy keeping deposits down and resisting oxidation, the oil holds its condition longer, which supports reliable air delivery and sensible service intervals. It meets DIN 51506 VD-L, a recognised air-compressor lubricant classification.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhere it fits\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eIt suits industrial and mobile air compressors in workshops, farms and manufacturing, both rotary screw and reciprocating types. Running an oil formulated for compressor duty, rather than a general industrial oil, is what keeps carbon and varnish off the valves and vanes over the long term.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eService and oil life\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eCompressor oil works hardest at high temperature, so keeping the compressor cooling clean and the oil at the right level helps it reach its full service life. Change the oil at the maker's recommended hours, or sooner in dusty or hot conditions, and replace or clean the air intake filter on schedule so grit does not shorten the oil's life or wear the air end. When changing, drain warm to carry out more of the old oil and any moisture, and confirm the ISO grade matches the compressor's requirement. Clean oil, changed on time, is what keeps valves and vanes free of the carbon and varnish that rob a compressor of efficiency.\u003c\/p\u003e","brand":"Valvoline","offers":[{"title":"Default Title","offer_id":45479052705871,"sku":"2036.51","price":1800.0,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0711\/9110\/1519\/files\/valvoline-2036-51-valcomp-46-compressor-oil-205l.webp?v=1793486720"},{"product_id":"1233-51","title":"1233.51 EPG Industrial Gear Oil 220 205L","description":"\u003cp\u003eValvoline EPG Industrial Gear Oil 220 is an ISO 220 mineral gear oil with sulphur-phosphorus extreme pressure additives for heavily loaded enclosed gear drives. Its heavier film and robust EP performance protect gears under sustained high load, while strong oxidation and foam resistance extend service intervals. The 205L drum is the bulk choice for plants with multiple gearboxes.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eA heavier grade for higher-load drives\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eSlower, more heavily loaded gears need a thicker oil to keep the teeth separated under pressure, which is where an ISO 220 grade earns its place over a lighter ISO 150. This mineral oil pairs that heavier film with sulphur-phosphorus extreme pressure (EP) additives, delivering strong load-carrying capacity for demanding enclosed gearboxes.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eHow the EP additives work\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eWhen load squeezes the film thin, the sulphur-phosphorus additives react at the contact points to form a protective layer that carries the pressure and prevents scuffing and welding of the gear faces. Combined with the ISO 220 film thickness, that gives strong protection for demanding, high-torque drives.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eClean, long service life\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe oil resists oxidation, foaming and corrosion so it stays serviceable through long intervals and keeps the gearbox internals protected. It meets AGMA 9005-EO2, DIN 51517 Part 3 and US Steel 224.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhere it fits\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eIt suits heavily loaded enclosed gearboxes in manufacturing and materials-handling equipment. Matching the ISO grade to the gearbox maker's recommendation is what delivers the intended life, so a lighter or heavier grade may suit faster or slower drives respectively.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eSelecting and maintaining the oil\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eAn ISO 220 grade suits heavier-loaded or slower drives, but the right choice is always the gearbox maker's specified viscosity, since a mismatched grade either runs hot or leaves the film too thin under load. Keep the oil clean and topped to level, guard against water ingress in wet environments, and change at the recommended interval or when analysis indicates. Draining the gearbox warm removes more of the old, contaminated oil and lets the fresh charge work as intended. Getting the viscosity and cleanliness right is what allows the extreme-pressure additives to protect the gears through the long, heavy duty cycles these drives run.\u003c\/p\u003e","brand":"Valvoline","offers":[{"title":"Default Title","offer_id":45479971487823,"sku":"1233.51","price":1802.7,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0711\/9110\/1519\/files\/valvoline-1233-51-epg-industrial-gear-oil-220-205l.webp?v=1793486789"},{"product_id":"1232-20","title":"1232.20 EPG Industrial Gear Oil 150 20L","description":"\u003cp\u003eValvoline EPG Industrial Gear Oil 150 is an ISO 150 mineral gear oil with sulphur-phosphorus extreme pressure additives, engineered for enclosed industrial gearboxes under heavy and shock loading. It combats the leading causes of gear failure, deposits, rust and wear, while resisting oxidation and foaming for long, reliable service. The 20L pack suits plant maintenance and individual gearbox changes.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eExtreme-pressure protection for enclosed gearboxes\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eGear systems fail from a short list of causes, chiefly deposits, rust and wear, and an industrial gear oil is judged on how well it combats all three. This ISO 150 mineral oil is formulated with sulphur-phosphorus extreme pressure (EP) additives for enclosed gearboxes under heavy and shock loading, so critical drives keep running.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eHow the EP additives work\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eUnder heavy or shock loading, the oil film between gear teeth is squeezed thin and metal comes close to metal. The sulphur-phosphorus EP additives react at those high-pressure contact points to form a protective layer that carries the load and prevents the scuffing and welding that destroy gear faces. The ISO 150 viscosity provides the film thickness that general-purpose industrial drives are designed around.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eClean, long service life\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eBeyond load carrying, the formulation resists oxidation, foaming and corrosion, which keeps the oil serviceable through long drain intervals and protects the gearbox internals between changes. It meets recognised industrial standards including AGMA 9005-EO2, DIN 51517 Part 3 and US Steel 224.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhere it fits\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eIt suits enclosed industrial gear drives in manufacturing, processing and materials-handling plant. Where a drive runs heavier or slower and needs a thicker film, a higher ISO grade is the better match, so selecting to the gearbox maker's viscosity recommendation gives the intended service life.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eSelecting and maintaining the oil\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eIndustrial gearboxes are designed around a specific ISO viscosity, so match the grade to the gearbox maker's recommendation rather than assuming a heavier oil is always better, since too high a viscosity can run hot and too low leaves the film thin. Keep the oil clean and at the right level, watch for water contamination in damp environments, and change at the recommended interval or when oil analysis shows it is due. On a first fill or an oil change, draining the box warm and flushing out old, contaminated oil gets the best from the fresh charge. Consistent viscosity and clean oil are what deliver the long gear life the EP additives are there to protect.\u003c\/p\u003e","brand":"Valvoline","offers":[{"title":"Default Title","offer_id":45480102625359,"sku":"1232.20","price":218.0,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0711\/9110\/1519\/files\/valvoline-1232-20-epg-industrial-gear-oil-150-20l.webp?v=1785301066"},{"product_id":"1232-51","title":"1232.51 EPG Industrial Gear Oil 150 205L","description":"\u003cp\u003eValvoline EPG Industrial Gear Oil 150 is an ISO 150 mineral gear oil fortified with sulphur-phosphorus extreme pressure additives for enclosed industrial gearboxes under heavy and shock loads. It protects against deposits, rust and wear while resisting oxidation and foaming. The 205L drum is the bulk option for plants running multiple gear drives and topping up from a dispensing setup.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eExtreme-pressure protection for enclosed gearboxes\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eGear systems fail from a short list of causes, chiefly deposits, rust and wear, and an industrial gear oil is judged on how well it combats all three. This ISO 150 mineral oil is formulated with sulphur-phosphorus extreme pressure (EP) additives for enclosed gearboxes under heavy and shock loading, so critical drives keep running.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eHow the EP additives work\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eUnder heavy or shock loading, the oil film between gear teeth is squeezed thin and metal comes close to metal. The sulphur-phosphorus EP additives react at those high-pressure contact points to form a protective layer that carries the load and prevents the scuffing and welding that destroy gear faces. The ISO 150 viscosity provides the film thickness that general-purpose industrial drives are designed around.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eClean, long service life\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eBeyond load carrying, the formulation resists oxidation, foaming and corrosion, which keeps the oil serviceable through long drain intervals and protects the gearbox internals between changes. It meets recognised industrial standards including AGMA 9005-EO2, DIN 51517 Part 3 and US Steel 224.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhere it fits\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eIt suits enclosed industrial gear drives in manufacturing, processing and materials-handling plant. Where a drive runs heavier or slower and needs a thicker film, a higher ISO grade is the better match, so selecting to the gearbox maker's viscosity recommendation gives the intended service life.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eSelecting and maintaining the oil\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eIndustrial gearboxes are designed around a specific ISO viscosity, so match the grade to the gearbox maker's recommendation rather than assuming a heavier oil is always better, since too high a viscosity can run hot and too low leaves the film thin. Keep the oil clean and at the right level, watch for water contamination in damp environments, and change at the recommended interval or when oil analysis shows it is due. On a first fill or an oil change, draining the box warm and flushing out old, contaminated oil gets the best from the fresh charge. Consistent viscosity and clean oil are what deliver the long gear life the EP additives are there to protect.\u003c\/p\u003e","brand":"Valvoline","offers":[{"title":"Default Title","offer_id":45480110686287,"sku":"1232.51","price":1802.7,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0711\/9110\/1519\/files\/valvoline-1232-51-epg-industrial-gear-oil-150-205l.webp?v=1793486790"},{"product_id":"1243-05","title":"1243.05 Chain \u0026 Cutter Bar Lubricant 5L","description":"\u003cp\u003eValvoline Chain and Cutter Bar Lubricant is a high-tack oil designed for industrial chains and chainsaw guide bars. Its non-throw formulation clings to fast-moving links and bar rails, resisting the fling-off that leaves cutting gear dry and wearing. The 5L pack is the practical size for chainsaw operators and small workshop chain drives.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eA lube that stays on fast-moving chains and bars\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eAt the speed a chain or cutter bar runs, centrifugal force strips a thin oil away in moments, leaving the pins, rollers and rails to wear. A high-tack, non-throw lubricant is built to defeat that, clinging to fast-moving links and bar rails instead of flinging off, so cutting and drive gear stay protected.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhy the tackiness matters\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eAt the speed a chain or cutter bar runs, centrifugal force strips thin oils away within moments, leaving the pins, rollers and rails unprotected. This lubricant is formulated with adhesion additives so the film stays where it is applied, maintaining lubrication on the load-bearing surfaces and cutting the metal-to-metal contact that drives wear and stretch.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eBuilt to work\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe oil is heavy-bodied enough to hold under load yet flows well enough to feed through an automatic bar oiler, so it suits both hand application and mechanised oiling systems. That combination keeps chains and bars protected across a working day.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhere it fits\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eIt suits chainsaws in forestry, orchard and property work, and the drive and conveyor chains found on workshop and industrial equipment. Anywhere a chain or bar runs fast enough to throw lubricant off, a non-throw film means less wear, smoother running and longer service life.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eBar oiling and chain care\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eOn a chainsaw, keep the automatic oiler set so the bar stays visibly wet in the cut, since a dry bar and chain wear and blue with heat very quickly, and check the oiler and clean the bar groove regularly so oil reaches the whole chain. On industrial and conveyor chains, apply enough to keep the pins and rollers protected without building a thick grit-holding layer, and re-lube on a schedule suited to the speed and environment. The non-throw formulation is what keeps the lube on the chain at speed, but it still needs applying to a reasonably clean chain to penetrate the joints where wear actually happens.\u003c\/p\u003e","brand":"Valvoline","offers":[{"title":"Default Title","offer_id":45480692940879,"sku":"1243.05","price":47.7,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0711\/9110\/1519\/files\/valvoline-1243-05-chain-and-cutter-bar-lubricant-5l.webp?v=1785301172"},{"product_id":"1243-20","title":"1243.20 Chain \u0026 Cutter Bar Lubricant 20L","description":"\u003cp\u003eValvoline Chain and Cutter Bar Lubricant is a high-tack oil for industrial chains and chainsaw guide bars, formulated with strong non-throw properties so it holds on under high speed and load. The 20L pack suits forestry crews, orchards and industrial operations lubricating chains and bars in volume, whether hand-applied or fed through an automatic oiler.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eA lube that stays on fast-moving chains and bars\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eAt the speed a chain or cutter bar runs, centrifugal force strips a thin oil away in moments, leaving the pins, rollers and rails to wear. A high-tack, non-throw lubricant is built to defeat that, clinging to fast-moving links and bar rails instead of flinging off, so cutting and drive gear stay protected.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhy the tackiness matters\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eAt the speed a chain or cutter bar runs, centrifugal force strips thin oils away within moments, leaving the pins, rollers and rails unprotected. This lubricant is formulated with adhesion additives so the film stays where it is applied, maintaining lubrication on the load-bearing surfaces and cutting the metal-to-metal contact that drives wear and stretch.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eBuilt to work\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe oil is heavy-bodied enough to hold under load yet flows well enough to feed through an automatic bar oiler, so it suits both hand application and mechanised oiling systems. That combination keeps chains and bars protected across a working day.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhere it fits\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eIt suits chainsaws in forestry, orchard and property work, and the drive and conveyor chains found on workshop and industrial equipment. Anywhere a chain or bar runs fast enough to throw lubricant off, a non-throw film means less wear, smoother running and longer service life.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eBar oiling and chain care\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eOn a chainsaw, keep the automatic oiler set so the bar stays visibly wet in the cut, since a dry bar and chain wear and blue with heat very quickly, and check the oiler and clean the bar groove regularly so oil reaches the whole chain. On industrial and conveyor chains, apply enough to keep the pins and rollers protected without building a thick grit-holding layer, and re-lube on a schedule suited to the speed and environment. The non-throw formulation is what keeps the lube on the chain at speed, but it still needs applying to a reasonably clean chain to penetrate the joints where wear actually happens.\u003c\/p\u003e","brand":"Valvoline","offers":[{"title":"Default Title","offer_id":45480699363407,"sku":"1243.20","price":189.0,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0711\/9110\/1519\/files\/valvoline-1243-20-chain-and-cutter-bar-lubricant-20l-0.webp?v=1785301173"}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0711\/9110\/1519\/collections\/Compressor-Slideway-Industrial-Gear-Oil.webp?v=1781693336","url":"https:\/\/geelongfiltersales.com.au\/collections\/industrial-oils.oembed","provider":"Geelong Filter Sales","version":"1.0","type":"link"}