45° Rubber Elbows (13)

45 degree rubber elbows make the gentler turns in air intake ducting on trucks, tractors, gensets and earthmoving gear, where a run only needs to change direction partway or step sideways around an obstruction. Used in pairs, they create an offset that a single 90 degree bend can't. Like other intake hose, they're moulded from heat- and ozone-resistant rubber that flexes with engine movement while keeping filtered air sealed in. Measure the outside diameter of the tube each end slides over, then clamp both ends properly. A split, soft or loose elbow on the clean side lets unfiltered dust straight into the engine, and because a leak lowers restriction rather than raising it, the indicator won't warn you.

Donaldson – P105547 – 45 degree rubber elbow, 6 inch – angled side view

13 products

  • Donaldson – P105547 – 45 degree rubber elbow, 6 inch – angled side view
    Vendor:
    Donaldson

    P105547 Rubber Elbow, 45 degree, 152 mm / 6.00 in diameter

    Regular price $77.30 AUD
    Sale price $77.30 AUD Regular price
  • Donaldson – P109021 – 45 degree rubber elbow, 5 inch – angled side view
    Vendor:
    Donaldson

    P109021 Rubber Elbow, 45 degree, 127 mm / 5.00 in diameter

    Regular price $63.80 AUD
    Sale price $63.80 AUD Regular price
  • Donaldson – P105545 – 45 degree rubber elbow, 4 inch – angled side view
    Vendor:
    Donaldson

    P105545 Rubber Elbow, 45 degree, 102 mm / 4.00 in diameter

    Regular price $57.30 AUD
    Sale price $57.30 AUD Regular price
  • Donaldson – P105544 – 45 degree rubber elbow, 3 inch – angled side view
    Vendor:
    Donaldson

    P105544 Rubber Elbow, 45 degree, 76 mm / 3.00 in diameter

    Regular price $45.70 AUD
    Sale price $45.70 AUD Regular price
  • Donaldson – P105548 – 45 degree rubber elbow, 7 inch – angled side view
    Vendor:
    Donaldson

    P105548 Rubber Elbow, 45 degree, 178 mm / 7.00 in diameter

    Regular price $112.00 AUD
    Sale price $112.00 AUD Regular price
  • Donaldson – P105546 – 45 degree rubber elbow, 5.5 inch – angled side view
    Vendor:
    Donaldson

    P105546 Rubber Elbow, 45 degree, 140 mm / 5.50 in diameter

    Regular price $70.10 AUD
    Sale price $70.10 AUD Regular price
  • Donaldson – P112606 – 45 degree rubber elbow, 8 inch – angled side view
    Vendor:
    Donaldson

    P112606 Rubber Elbow, 45 degree, 203 mm / 8.00 in diameter

    Regular price $201.30 AUD
    Sale price $201.30 AUD Regular price
  • Donaldson – P109331 – 45 degree rubber elbow, 3.5 inch – angled side view
    Vendor:
    Donaldson

    P109331 Rubber Elbow, 45 degree, 89 mm / 3.50 in diameter

    Regular price $59.80 AUD
    Sale price $59.80 AUD Regular price
  • Donaldson – P105541 – 45 degree rubber elbow, 2 inch – angled side view
    Vendor:
    Donaldson

    P105541 Rubber Elbow, 45 degree, 51 mm / 2.00 in diameter

    Regular price $46.70 AUD
    Sale price $46.70 AUD Regular price
  • Donaldson – P105543 – 45 degree rubber elbow, 2.5 inch – angled side view
    Vendor:
    Donaldson

    P105543 Rubber Elbow, 45 degree, 64 mm / 2.50 in diameter

    Regular price $53.50 AUD
    Sale price $53.50 AUD Regular price
  • Donaldson P114316 Rubber Elbow, 45 degree, 114 mm / 4.50 in diameter
    Vendor:
    Donaldson

    P114316 Rubber Elbow, 45 degree, 114 mm / 4.50 in diameter

    Regular price $67.80 AUD
    Sale price $67.80 AUD Regular price
  • Donaldson – P105542 – 45 degree rubber elbow, 2.25 inch – angled side view
    Vendor:
    Donaldson

    P105542 Rubber Elbow, 45 degree, 57 mm / 2.25 in diameter

    Regular price $53.10 AUD
    Sale price $53.10 AUD Regular price
  • Donaldson – P114313 – 45 degree rubber elbow, 10 inch – angled side view
    Vendor:
    Donaldson

    P114313 Rubber Elbow, 45 degree, 254 mm / 10.00 in diameter

    Regular price $337.90 AUD
    Sale price $337.90 AUD Regular price

When should I use a 45 degree elbow?

Use one when the run needs a partial change of direction rather than a full right angle. Pairs of 45s make neat offsets around frame rails, hoses and brackets, and a 45 often lines up better than forcing a straight hose into a curve, which can kink and restrict airflow. Keep bends clear of exhaust manifolds and turbo housings, or shield them, since radiant heat hardens rubber quickly.

What size elbow do I need?

The size that matches the pipe outside diameter at each end. Elbows are listed by nominal diameter in millimetres and inches, so measure the pipe or spigot, not the old rubber, which may have stretched. Check the leg length leaves enough grip for a clamp.

Are rubber intake elbows suitable for boost pressure?

No. They're designed for the low-pressure clean side between the air cleaner and turbo inlet. Pipework after the turbo needs reinforced silicone connectors rated for heat and pressure.

  • Pipe outside diameter
  • Bend angle needed
  • Leg length and clamp room
  • Temperature rating for the position
  • Clamp size for each end

Need a full right angle? See 90 degree rubber elbows. Straight joints are in hump hoses and reducers, and clamps finish the job. Ask us to match an old elbow.

Do the 45 degree elbows come in the same sizes as the 90s?

Yes. All 13 sizes, from 50.8 mm (P105541) to 254 mm (P114313), have an equal-diameter 90 degree elbow in the same size, so you can mix 45 and 90 degree bends in one run without changing pipe size. The table below pairs each 45 with its matching 90.

Match the inside diameter to the outside of your pipe, then check the bend radius in the table: it runs from 51 mm on the smallest to 216 mm on the 254 mm elbow, and it decides how much room the bend takes.

Is there a reducing 45 degree elbow?

No. Every 45 degree elbow we list has the same diameter at both ends. Where the pipe size changes at the bend, you have two ways to do it:

  • Make it a right angle: one of our nine 90 degree reducer elbows turns and changes size in one part.
  • Keep the 45: add a hump reducer on the straight run before or after it.

The second way adds a joint and two more clamps, and downstream of the air cleaner every joint is a potential dust path straight into the engine. Check both clamps at each filter service.