Spin-on Fuel Filters (279)

Spin-on fuel filters thread straight onto the filter head as a sealed can, with no loose element to handle and less chance of dirt getting in at service time. These are filter-only cans for diesel trucks, tractors, machinery and gensets, used in primary or secondary positions and usually paired with a separate water separator. Micron rating and position decide the match, followed by thread and media. Fit the wrong can and it still seals and runs, while the fine particles it lets through wear the pump and injectors well before any warning appears. On a common-rail engine that can mean a full injector set. Search the number off your current can, or read the selection guide below.

Spin-on Fuel Filters

279 products

  • Fleetguard FF167A Fuel Filter – Can Type, Rolled Paper
    Vendor:
    Fleetguard

    FF167A Fuel Filter- Can Type, Rolled Paper

    Regular price $8.50 AUD
    Sale price $8.50 AUD Regular price
  • Baldwin BF825 Fuel Filter – Can Type
    Vendor:
    Baldwin

    BF825 Fuel Filter- Can Type

    Regular price $9.00 AUD
    Sale price $9.00 AUD Regular price
  • Baldwin BF790 Fuel Filter – Spin-on
    Vendor:
    Baldwin

    BF790 Fuel Filter- Spin-on

    1 in stock
    Regular price $25.50 AUD
    Sale price $25.50 AUD Regular price
  • Baldwin BF7608 Fuel Filter – Spin-on
    Vendor:
    Baldwin

    BF7608 Fuel Filter- Spin-on

    Regular price $25.50 AUD
    Sale price $25.50 AUD Regular price
  • Fleetguard FF5114 Fuel Filter – Spin-on, 20 micron
    Vendor:
    Fleetguard

    FF5114 Fuel Filter- Spin-on, 20 Mic

    4 in stock
    Regular price $14.60 AUD
    Sale price $14.60 AUD Regular price
  • Fleetguard FF5040 Fuel Filter – Spin-on
    Vendor:
    Fleetguard

    FF5040 Fuel Filter- Spin-on

    4 in stock
    Regular price $23.00 AUD
    Sale price $23.00 AUD Regular price
  • Baldwin BF940 Fuel Filter – Spin-on
    Vendor:
    Baldwin

    BF940 Fuel Filter- Spin-on

    6 in stock
    Regular price $21.00 AUD
    Sale price $21.00 AUD Regular price
  • Fleetguard FF5229 Fuel Filter – Spin-on
    Vendor:
    Fleetguard

    FF5229 Fuel Filter- Spin-on

    2 in stock
    Regular price $22.70 AUD
    Sale price $22.70 AUD Regular price
  • Fleetguard FF5135 Fuel Filter – Spin-on, Drain, 16 micron
    Vendor:
    Fleetguard

    FF5135 Fuel Filter- Spin-on, Drain, 16 Mic

    Regular price $24.60 AUD
    Sale price $24.60 AUD Regular price
  • Fleetguard FF5018 Fuel Filter – Spin-on, 18 micron
    Vendor:
    Fleetguard

    FF5018 Fuel Filter- Spin-on, 18 Mic

    3 in stock
    Regular price $13.50 AUD
    Sale price $13.50 AUD Regular price
  • Baldwin BF954 Fuel Filter – Spin-on
    Vendor:
    Baldwin

    BF954 Fuel Filter- Spin-on

    4 in stock
    Regular price $14.40 AUD
    Sale price $14.40 AUD Regular price
  • Fleetguard FF4052A Fuel Filter – Can Type, 12 micron
    Vendor:
    Fleetguard

    FF4052A Fuel Filter- Can Type, 12 Mic

    2 in stock
    Regular price $23.60 AUD
    Sale price $23.60 AUD Regular price
  • Fleetguard FF5159 Fuel Filter – Spin-on, Threaded Port
    Vendor:
    Fleetguard

    FF5159 Fuel Filter, Spin-on, Threaded Port

    3 in stock
    Regular price $29.60 AUD
    Sale price $29.60 AUD Regular price
  • Fleetguard FF5087 Fuel Filter – Spin-on, 15 micron
    Vendor:
    Fleetguard

    FF5087 Fuel Filter- Spin-on, 15 Mic

    2 in stock
    Regular price $14.20 AUD
    Sale price $14.20 AUD Regular price
  • Fleetguard FF167 Fuel Filter – Can Type, Pleated Paper
    Vendor:
    Fleetguard

    FF167 Fuel Filter- Can Type, Pleated Paper

    Regular price $11.90 AUD
    Sale price $11.90 AUD Regular price

Do I need a fuel filter or a water separator?

If your engine has a separate water trap, a filter-only spin-on is usually right. Filter-only cans have no drain or bowl, so fitting one where a separator belongs removes the system's water protection. Check whether the old can had a drain valve, bowl thread or sensor port before you order.

Choosing a spin-on fuel filter

  • Micron rating: the finer secondary protects the injection system, so match the rating on your old can.
  • Primary or secondary: they look alike but filter differently, and many part numbers say which they are.
  • Thread: confirm the head thread, as imperial and metric threads can look close.
  • Media: synthetic media generally filters finer and holds more dirt than cellulose, while wire mesh cans are coarse screens only.
  • Construction: some heads need a standpipe filter or a particular can design, so check the head.

Fitting tips for spin-on fuel filters

Wet the gasket with clean fuel, spin the can on until the seal touches, then tighten by hand as directed on the filter. Don't pre-fill a secondary filter with unfiltered fuel, because that puts dirt straight on the clean side. Prime the system as the OEM manual describes and check for leaks with the engine running, as an air leak at the head causes hard starting and rough running.

Need water separation in the same can? See spin-on fuel water separators. Cartridge housings take fuel filter cartridge elements, and full service sets are in 4WD and truck filter kits.

What's the difference between Fleetguard StrataPore and NanoNet fuel filters?

Both are Fleetguard synthetic media; NanoNet is the fine end of the range.

  • StrataPore: a multilayer melt-blown synthetic media that grades capture through its depth, used across Fleetguard's primary and secondary filters and separators. Examples: FF2200 at 98.7% at 13.7 micron and FF5612 at 98% at 5.8 micron.
  • NanoNet: continuous polymeric media that is glass-free and contains no cellulose, which removes the possibility of short fibres releasing into the engine. Fleetguard describe it as their highest level of injector protection. The FF63054NN for Cummins B and L series engines uses it.

Choose by the part number your engine calls for, not the media name. The engine maker's requirement for that position decides the media.

Two spin-on fuel filters share a thread. Can I fit either one?

No. Spin-ons that share a thread can be built for different positions, and the position decides how the can is built.

  • Primary, suction side: works under vacuum ahead of the transfer pump, with a coarser rating for capacity. The FF5624 is listed as a 20 micron primary.
  • Secondary, pressure side: works under positive pressure after the pump, with a finer rating. Fleetguard list the FF2200 as a pressure-side filter.

A suction-side filter on the pressure side risks bursting, and a pressure-side filter on the suction side can collapse. Order by part number, not thread, and if your machine has two spin-ons, note which came off where before you remove them.

What should I check before fitting a replacement spin-on fuel filter?

Check these against the filter you're taking off, using the specifications tab:

  • Thread: for example M72 x 2 on the FF2200 or M20 x 1.5 on the FF5612.
  • Gasket outer diameter: a different gasket size won't seal on the head even if the thread starts.
  • Position: primary or secondary, suction or pressure side.
  • Bottom end: plain, drain or threaded port, such as the FF5159. If the old filter had a drain, sensor or bowl underneath, the new one needs the same base. Bowls and replacement heads are in fuel filter bowls, heads and assemblies.
  • Standpipe and length: some heads need a standpipe, and a longer can may not clear the chassis.

Prime and bleed the fuel system as your engine manual describes before starting.

Can I fit a finer micron fuel filter than the original for extra protection?

Not in place of the original, and rarely in the primary position. A finer primary can reach its dirt-holding capacity sooner, so it may need changing well before the service interval.

The better approach is staging: a coarser, high-capacity filter ahead of the specified one. Fleetguard's example is a 25 micron StrataPore filter fitted upstream of a 10 micron original-equipment filter, which can as much as triple the service life of the system. Add capacity upstream, such as one of our add-on diesel fuel filter kits, and keep the engine's own filters at the rating the engine maker specified.