Bulk Fuel & Lube Filtration (43)

Bulk fuel and lube filtration cleans diesel and oil at the storage tank, so contamination is stopped once at the dispenser instead of in every machine that fills from it. Farms, mine sites, depots, workshops and service trucks all run it, from a single overhead tank to a full dispensing rack. Stored fuel collects water from condensation and dirt through the vent, and new oil isn't always as clean as a modern hydraulic system or common-rail engine needs.

The choice starts with the fluid and how it moves: diesel or oil, pumped or gravity-fed, fixed or portable. Get it wrong and on-board filters block early, injectors and hydraulic pumps take the wear, and the cost lands on every machine in the fleet. Pick the sub-category that matches your setup.

Bulk Fuel & Lube Filtration

43 products

  • Donaldson P567392 T.R.A.P Breather – Glass-Filled Nylon, 1/4 NPT, Mini, 3um, 85 Lpm
    Vendor:
    Donaldson

    P567392 T.R.A.P Breather, Glass-Filled Nylon, 1/4 NPT, Mini, 3um, 85 lpm

    2 in stock
    Regular price $59.90 AUD
    Sale price $59.90 AUD Regular price
  • Donaldson P565857 T.R.A.P Breather – Epoxy-coated Steel, 3/4 NPT, 3um, 708 Lpm
    Vendor:
    Donaldson

    P565857 T.R.A.P Breather, Epoxy-coated Steel, 3/4 NPT, 3um, 708 lpm

    1 in stock
    Regular price $99.50 AUD
    Sale price $99.50 AUD Regular price
  • Donaldson P566037 T.R.A.P Breather – Epoxy-coated Steel, G3/4, 3um, 708 Lpm
    Vendor:
    Donaldson

    P566037 T.R.A.P Breather, Epoxy-coated Steel, G3/4, 3um, 708 lpm

    2 in stock
    Regular price $99.50 AUD
    Sale price $99.50 AUD Regular price
  • Donaldson DBB0248 CLFS Filter for Ethanol-Free Fluids – Water Absorbing Media, 20um, 246 Lpm
    Vendor:
    Donaldson

    DBB0248 CLFS Filter for Ethanol-Free Fluids, Water Absorbing Media, 20um, 246 lpm

    1 in stock
    Regular price $271.20 AUD
    Sale price $271.20 AUD Regular price
  • Donaldson DBB8777 CLFS Winter Fuel Filter for All Diesel Fuels, 7um, 246 lpm
    Vendor:
    Donaldson

    DBB8777 CLFS Winter Fuel Filter for All Diesel Fuels, 7um, 246 lpm

    Regular price $293.60 AUD
    Sale price $293.60 AUD Regular price
  • Donaldson P567390 Mini T.R.A.P. hydraulic reservoir breather with 3/8 NPT thread in black
    Vendor:
    Donaldson

    P567390 Breather, Trap

    Regular price $59.80 AUD
    Sale price $59.80 AUD Regular price
  • LUBESMART AF-UF-FF25-1 Fuel Filter Assembly – 1 Inch BSP Ports, 10um Filter Cartridge, Translucent Bowl and Drain
    Up to $32.90 off
    Vendor:
    A-FLO Equipment

    AF-UF-FF25-1 Fuel Filter Assembly, 1" BSP Ports, 10um Filter Element, Translucent Bowl & Drain, up to 95 lpm

    Regular price $131.00 AUD
    Sale price $131.00 AUD Regular price $163.90 AUD
  • PIUSI F00611B00 Clear Captor Filter Assembly – 2x F00611030 5um Particulate Filter, 1 Inch BSP Inlet/outlet, 100 Lpm
    Vendor:
    PIUSI

    F00611B00 Clear Captor Filter Assembly, 2x F00611030 5um Particulate Filter, 1" BSP inlet/outlet, 100 lpm

    1 in stock
    Regular price $286.00 AUD
    Sale price $286.00 AUD Regular price
  • Donaldson P506159 T.R.A.P Breather Assembly – Brass G1-1/2 Connection, 3um, Diesel and Oil Tanks Up to 500 Lpm
    Vendor:
    Donaldson

    P506159 T.R.A.P Breather Assembly, Brass G1-1/2 Connection, 3um, Diesel & Oil Tanks up to 500 lpm

    Regular price $564.00 AUD
    Sale price $564.00 AUD Regular price
  • Donaldson P923075 TRAP breather element in blue urethane for moisture and particulate control
    Vendor:
    Donaldson

    P923075 T.R.A.P Breather Element, Urethane, 1-1/4" BSP, 3um, 500 lpm

    1 in stock
    Regular price $256.10 AUD
    Sale price $256.10 AUD Regular price
  • Donaldson P564669 T.R.A.P Breather – Glass-Filled ABS, 1" NPT, 3um, 1274 Lpm
    Vendor:
    Donaldson

    P564669 T.R.A.P Breather, Glass-Filled ABS, 1" NPT, 3um, 1274 lpm

    Regular price $158.80 AUD
    Sale price $158.80 AUD Regular price
  • Donaldson P566151 T.R.A.P Breather – Glass-Filled ABS, 1 Inch NPT, 3um, 1274 Lpm
    Vendor:
    Donaldson

    P566151 T.R.A.P Breather, Glass-Filled ABS, 1" NPT, 3um, 1274 lpm

    1 in stock
    Regular price $106.70 AUD
    Sale price $106.70 AUD Regular price
  • Donaldson X011408 Bu.F.S.S Bulk Fuel Service System – 12V, 57 Lpm
    Vendor:
    Donaldson

    X011408 Bu.F.S.S Bulk Fuel Service System, 12V, 57 lpm

    Regular price $9,730.80 AUD
    Sale price $9,730.80 AUD Regular price
  • Donaldson P570330 Filter Head, 1 1/4" NPTF Ports, Clean Solutions
    Vendor:
    Donaldson

    P570330 Filter Head, 1 1/4" NPTF Ports, Clean Solutions

    Regular price $267.30 AUD
    Sale price $267.30 AUD Regular price
  • Donaldson P570329 Filter Head, SAE-20 Ports, Clean Solutions
    Vendor:
    Donaldson

    P570329 Filter Head, SAE-20 Ports, Clean Solutions

    Regular price $267.30 AUD
    Sale price $267.30 AUD Regular price

What does bulk filtration actually do?

It puts a filter between storage and the machine, so fuel and oil are cleaned as they're dispensed. One correctly sized system protects every engine, gearbox and hydraulic circuit that fills from that tank, and it takes load off the filters on board each machine.

Which bulk filtration product do I need?

Start with the job, then follow the link.

What decides the size and micron rating?

Flow and fluid. A filter rated below your pump's output restricts flow and blocks early, so size it at or above the pump's maximum. Diesel for common-rail engines usually calls for a finer rating and water control, while thicker oils need a coarser grade or larger element to keep pressure drop down. Engine and equipment makers often state a fuel or oil cleanliness target as an ISO 4406 code, so check the OEM manual.

For the transfer side, see diesel pumps, reels and tanks and oil dispensing equipment, or talk to us about an unusual tank layout.

Which bulk filtration section do I need for my tank setup?

Start with how the fluid leaves the tank, then what the fluid is.

Filtering fuel on the vehicle, ahead of the engine's own filter, is a different job: see our HPCR diesel filter kits.

Our diesel supplier delivers to standard. Why filter it again at the dispenser?

Because fuel that meets the delivery standard can still be well short of what a common-rail engine needs. Donaldson puts typical diesel going into equipment at ISO 22/21/18. That's 20,000 to 40,000 particles of 4 micron and larger in every millilitre, typically with 200 to 300 ppm of water. The eye only sees particles down to about 40 micron, so fuel that looks clean proves nothing. Compare that with Donaldson's recommended diesel target of ISO 14/13/11: eight code steps on each of the first two numbers, and each step roughly halves the particle count. Storage adds to the load too: every time the tank draws down, air comes in through the vent, carrying dust and moisture.

Filtering at the dispenser stops that dirt plugging the on-board fuel filters early, and every machine filled from the tank gets clean fuel instead of each engine's own filter doing all the work. Use the table on this page to match a kit to your tank.

Which cleanliness target should I filter diesel, hydraulic oil and gear oil to?

The equipment maker's figure, if it gives one. Where it doesn't, Donaldson's recommended targets for bulk fluids are:

  • Diesel fuel: ISO 14/13/11. Our 4 micron Donaldson dispenser kits and the Bu.F.S.S fuel cart are rated to reach it in a single pass.
  • Hydraulic and transmission oil: ISO 16/14/11.
  • Heavy gear and engine oil: ISO 18/16/13.

Filter to the target, not finer. Donaldson's guidance is not to over-filter, because going too fine can strip beneficial additives from oil. The element for each oil target is on our Bulk hP filter page for high-pressure reel lines, and our replacement element page for kits and carts.

Do I need water removal as well as particulate filtration?

If there is any chance of free water in the tank, yes. A particulate element is built to stop dirt, not to hold water back. Here's where water removal sits in our range:

Keeping wet air out of the tank in the first place is the breather's job: see our T.R.A.P. breathers.

When should I change the elements in a bulk filter kit?

Change them on pressure drop, not the calendar. As an element loads with dirt, the pressure difference across it rises.

Most of our Donaldson kits list a pressure gauge in their contents. Note the reading with a new element at your normal flow and watch it climb. Element life depends on how dirty the incoming fuel is, so a site taking poor deliveries will change elements more often than one with clean supply. If you'd rather work to a set point, the heads take a service indicator: see our filter heads.

Replacement elements for our Donaldson kits and carts are in Clean & Dry replacement filters.

How do flow rate and cold weather affect bulk filter sizing?

Pressure drop rises with flow and with viscosity, so size for your pump's maximum flow and the coldest fluid you will pump.

Donaldson's sizing guide aims for a new-system pressure drop under 0.69 bar for fuel and under 1 bar for lubricants. Viscosity is the variable that gets missed: an ISO VG 32 oil that flows like diesel at 40°C goes past 2,000 cSt at -20°C. Size on the temperature of the fluid in storage, not the lowest air temperature, which usually overstates it.

If one filter can't keep pressure drop down at your flow, add filters in parallel to split the flow. For diesel dispensers our Donaldson kits run from 121 lpm to 375 lpm. For oils, check the element's recommended viscosity on our replacement element page before you buy.