Performance & Racing Oils (3)

Performance and racing oils for modified, high-output and competition engines. They're formulated for what a race or performance engine sees: high rpm, high oil temperatures, heavy bearing loads and tight tolerances, often with more anti-wear additive than current road-car specs allow. Builders choose them on base oil, on viscosity, especially the hot second number, and on how the oil holds up at the temperatures the engine actually runs.

Change intervals are short and set by the engine builder, not a road service schedule. Fit a thin road oil to a high-output build and the bearings and cam lobes take the punishment. Stretch a racing oil to road-car intervals and it's worn out well before the drain. Check the notes below before using one on the street.

Performance & Racing Oils

3 products

  • Valvoline 1166.05 VR1 Semi Synthetic Racing Oil 10W40 5L
    Vendor:
    Valvoline

    1166.05 VR1 Semi Synthetic Racing Oil 10W40 5L

    Regular price $74.95 AUD
    Sale price $74.95 AUD Regular price
  • Valvoline 1045.05 Racing Formula 50 25W60 Engine Oil5L
    Vendor:
    Valvoline

    1045.05 Racing Formula 50 25W60 Mineral Engine Oil 5L

    6 in stock
    Regular price $69.00 AUD
    Sale price $69.00 AUD Regular price
  • Valvoline 908786 VR1 10W60 Synthetic Racing Oil 5L
    Vendor:
    Valvoline

    908786 VR1 10W60 Synthetic Racing Oil 5L

    2 in stock
    Regular price $129.00 AUD
    Sale price $129.00 AUD Regular price

Can you use racing oil in a road car?

Sometimes, but check the label first. Some racing oils carry anti-wear additive levels above what catalytic converters tolerate over time, and some aren't certified to any API or ACEA road category. If the car is under warranty or relies on a catalytic converter, use a road-certified oil unless the oil maker says the racing oil suits road use.

Which viscosity does a performance engine need?

The one the engine builder specifies. Heavier hot grades suit engines built with larger bearing clearances or that run very high oil temperatures. A modified engine that keeps factory clearances usually runs best on the grade its maker lists, or close to it.

Choosing a racing oil

  • The grade on the engine builder's build sheet.
  • Base oil: full synthetic for the highest temperatures, mineral where the builder prefers it for older or flat-tappet race engines.
  • Anti-wear additive level, important for flat-tappet camshafts.
  • Road certification if the vehicle is registered or has a catalytic converter.
  • Drain interval: short, and ideally guided by oil analysis.

For everyday cars see synthetic engine oils. Track days also need high-boiling-point brake fluid, and a fresh spin-on oil filter belongs with every change. Building something special? Ask us about grades.

Which racing oil suits my engine?

Choose by base oil, grade and valvetrain:

  • VR1 Racing 10W-60: synthetic, ACEA A3/B4 and API SL/SM, for high-performance turbo and non-turbo petrol engines under high shear, heat and rpm in fast road, track and motorsport use. Also recommended where Fiat 9.55535.H3 is specified.
  • VR1 Racing 10W-40: semi-synthetic with a raised ZDDP anti-wear level for flat-tappet cams and high-load valvetrains. API SJ/CD.
  • Racing Formula 50 25W-60: mineral, with a heavy 60-weight film for engines that run hot and hard, including high-clearance builds. API SJ/CD.

If your engine builder has specified a grade, use that.

Can I run these racing oils in a road car with a catalytic converter or DPF?

Not the VR1 oils. Valvoline does not recommend VR1 Racing 10W-60 for vehicles fitted with aftertreatment systems or catalytic converters, and VR1 Racing 10W-40 isn't intended for modern engines with catalysts and particulate filters that need a low-SAPS oil, because of its raised zinc and phosphorus level.

Racing Formula 50 25W-60 is a specialist heavy-film oil, not a general road oil, and a 25W-60 slows cold flow in an engine designed around a light grade. For a road car with a cat or DPF, use the grade and spec in the owner's manual from our synthetic or semi-synthetic range.

Which oil should I use in a flat-tappet engine?

VR1 Racing 10W-40, unless your cam maker or engine builder specifies something else. It's a semi-synthetic built around a raised ZDDP (zinc and phosphorus) anti-wear level, which forms a sacrificial protective layer at high-contact points such as the cam lobe and lifter.

Modern low-SAPS road oils run less ZDDP to protect emissions hardware, which can leave a flat-tappet valvetrain short of protection. Follow your cam maker's break-in advice on top of the oil choice.