Diesel Hose Reels (2)

Diesel hose reels keep a refuelling hose wound, protected and off the ground at a depot bowser, on a service truck or on a fuel trailer. A spring-rewind reel pulls the hose back after each fill, so it isn't dragged across concrete or left lying around as a trip hazard. Hose bore and length decide the choice first, because the reel has to hold the hose and the hose has to carry the pump's flow without choking it.

Then check the pressure rating against your pump, and note that both reels here ship bare, so the hose is ordered separately. A hose left on the ground gets kinked, cut and coated in grit that ends up at the nozzle. Measure the reach to your furthest filler before ordering.

Diesel Hose Reels

2 products

  • Graco 24P468 XD 50 Series Bare Diesel Hose Reel, 1-1/2" – left-front view
    Vendor:
    Graco

    24P468 XD 50 Series Bare Diesel Hose Reel, 1-1/2"

    Regular price $4,015.50 AUD
    Sale price $4,015.50 AUD Regular price
  • Graco 24P318 XD 40 bare hose reel in yellow with 90 degree inlet elbow
    Vendor:
    Graco

    24P318 XD 40 Series Bare Air/Water/Diesel Hose Reel, C Spring

    Regular price $3,330.80 AUD
    Sale price $3,330.80 AUD Regular price

Spring rewind or manual hose reel?

Spring rewind suits frequent use, and a manual crank reel suits long, heavy hoses or occasional use. A spring reel with a latching ratchet holds the hose at any length and retracts it with a short pull. Always walk the hose back rather than letting it fly, because a fast rewind damages the nozzle and the reel's guide arm.

What size hose reel do I need?

Match the hose bore to the pump outlet and nozzle inlet, then pick a length that reaches without slack. A long hose with a narrow bore cuts flow noticeably on battery pumps. Each reel is rated for a maximum hose bore and length, and an overfilled reel won't rewind fully. Compare reels on these points:

  • Hose inside diameter
  • Hose length and reach to the filler
  • Working pressure against your pump's output
  • Spring rewind or manual crank
  • Supplied bare or with hose fitted
  • Mounting: floor, wall, ceiling or vehicle
  • Hose and swivel rated for diesel, or multi-fluid

How do I mount and maintain a diesel hose reel?

Bolt it to a solid surface that can take the pull of the hose, with the outlet facing the direction you'll draw from. Check the swivel for weeping fuel, which means its seals need replacing, and inspect the hose for cracking and abrasion where it runs over the guide rollers. Fuel-rated hose only: a water or air hose won't last in diesel.

Fit an automatic shut-off diesel nozzle on the end, pair it with an electric diesel transfer pump, compare hose reels for other fluids, or talk to us about mounting.

XD 40 or XD 50: which Graco diesel reel do I need?

Pick by the bore of the diesel hose you'll run.

  • 24P318 XD 40: takes 1" (25 mm) diesel hose up to 15 m, with 1" NPT inlet and outlet and a C spring. Fit a different hose and inlet kit and the same reel runs air, water or waste oil evacuation instead.
  • 24P468 XD 50: Graco's large-bore diesel reel, taking 1-1/4" or 1-1/2" hose at 15 m, with 1-1/2" NPT ports.

Both are rated to 41 bar and -40°C to 82°C, indoors or out. If your pump and nozzle run a 1" line, such as one ending in the 1" FS-AL120 nozzle, the XD 40 matches it; go to the XD 50 when the delivery line is bigger than 1".

Can I run diesel through a RAASM oil reel?

No. RAASM rates its oil reels for oils and similar products including antifreeze, and its 540 Series listing says they are not for fuels, DEF or water-based fluids. Their polyurethane seals are specified for oil.

Keep RAASM reels on oil lines (see oil hose reels). For diesel, use the Graco 24P318 or 24P468.

What do I need to order with a bare Graco diesel reel?

The reel ships bare with its inlet elbow, so add the hose, a ball stop kit and Graco's inlet hose kit, then a nozzle.

  • Diesel hose: for the XD 50, Graco's 24R114 (1-1/2" x 15 m) or 24R110 (1-1/4" x 15 m). For the XD 40, a 1" diesel hose up to 15 m.
  • Ball stop kit, sized to the hose: 24R061 for 1-1/2" and 24R060 for 1-1/4".
  • Inlet hose kit: Graco requires a flexible hose between the reel inlet and the supply: 24R115 on the XD 40 for diesel and 24R117 on the XD 50. Graco rates these at 17 bar and 10 bar, which sets the working limit of the line.
  • Nozzle: an automatic nozzle from diesel nozzles.

The Graco hose, ball stop and inlet kits aren't listed on our site; they're available on request, so ask for them with the reel.

Where can I mount a Graco diesel reel?

On the floor or a truck bed, and the XD 40 can also go overhead.

  • XD 40 24P318: floor, truck bed, or overhead with Graco's 237932 mounting kit and 24R076 support arm, up to 4.6 m high. It weighs 56.7 kg dry.
  • XD 50 24P468: floor or truck bed only, up to 2.4 m high, because the overhead kits are for the XD 40. It weighs 73.5 kg dry.

On a service truck the reel must be bonded (grounded) to the truck. Size the mount for the reel plus a hose full of diesel, not the dry weight alone.