Silicone Charge Air Connectors (4)

Silicone charge air connectors join the boosted pipework between the turbocharger, the intercooler and the intake manifold on trucks, tractors, gensets and off-highway machines. Multi-ply reinforced silicone handles the heat and pressure on that side of the engine far better than rubber intake hose, and resists oil, coolant and ozone. Straight humps and bellows-style connectors flex with engine movement and slight pipe misalignment, so the joint isn't strained every time the engine rocks on its mounts. Match the bore to the pipe outside diameter, check the length, and confirm the pressure and temperature rating suits the engine. A split or blown-off boost hose costs power and fuel straight away, and can push exhaust temperatures up.

Donaldson – P532944 – silicone charge air bellows, 4 inch – angled side view

4 products

  • Donaldson – P535573 – silicone charge air bellows, 4 inch – angled side view
    Vendor:
    Donaldson

    P535573 Silicone Charge Air Bellows, 102 mm / 4.00 in diameter, 203 mm long, 3 rings

    Regular price $135.00 AUD
    Sale price $135.00 AUD Regular price
  • Donaldson – P532944 – silicone charge air bellows, 4 inch – angled side view
    Vendor:
    Donaldson

    P532944 Silicone Charge Air Bellows, 102 mm / 4.00 in diameter, 152 mm long, 3 rings

    Regular price $98.10 AUD
    Sale price $98.10 AUD Regular price
  • Donaldson – P535572 – silicone charge air bellows, 3.5 inch – end and side views
    Vendor:
    Donaldson

    P535572 Silicone Charge Air Bellows, 89 mm / 3.50 in diameter, 152 mm long, 3 rings

    Regular price $215.80 AUD
    Sale price $215.80 AUD Regular price
  • Donaldson – P532960 – silicone charge air hump hose, 2.5 inch – angled side view
    Vendor:
    Donaldson

    P532960 Silicone Charge Air Hump Hose, 64 mm / 2.50 in diameter, 140 mm long

    Regular price $75.20 AUD
    Sale price $75.20 AUD Regular price

What does a charge air connector do?

It carries pressurised intake air across the gaps between turbo, charge air cooler and manifold while letting each part move on its own. The flexible hump or bellows soaks up vibration and heat growth that would crack a rigid joint. On electronically managed diesels, even a small boost leak can set fault codes, so treat oily residue or a hiss at a joint as a job for today.

Hump hose or bellows?

Choose by how much movement the joint has to absorb. A single hump suits modest movement in a short gap. Multi-ring bellows connectors handle more misalignment and travel, which is why they're common between a frame-mounted cooler and an engine-mounted turbo.

How do I stop boost hoses blowing off?

Start with clean, oil-free pipe ends that have a bead or flare, and give each end enough engagement. Fit constant torque clamps, lined where possible to protect the silicone, and tighten to the clamp maker's figure. Recheck after the first few heat cycles, since silicone settles.

  • Pipe outside diameter at each end
  • Overall length and gap to bridge
  • Single hump or multi-ring bellows
  • Pressure and temperature rating
  • Clamp type and size

Pair connectors with constant torque clamps. Clean-side intake joints are in hump hoses and reducers, and the full range is in air intake and exhaust parts. Ask us to match a hose.

Which charge air connector fits my boost pipe?

Match the bore to the pipe outside diameter, then the length to the gap:

  • 64 mm pipe: P532960, Nomex-reinforced single hump, 140 mm long.
  • 89 mm pipe: P535572, 3-ring bellows, 152 mm long.
  • 102 mm pipe: P532944 at 152 mm or P535573 at 203 mm, both 3-ring bellows.

Allow for at least 32 mm of beaded pipe inside each end. All four are 4-ply silicone rated to 40 psi (276 kPa) working pressure and 260°C, so check that your engine's boost pressure and charge air temperature in the OEM data sit inside those ratings. Replacing an OEM hose by number? Each listing carries cross references, for example Cummins 50000438 for the P535573. For another size, send us the pipe diameter and length.

Which clamps go with a charge air connector?

Two lined constant torque clamps per connector, one at each end:

Sit each clamp behind the bead on the pipe and tighten to 7.9–8.5 Nm (70–75 in·lb). The spring-loaded housing keeps the grip as the joint heats up and cools down, where a plain worm-drive clamp works loose, and the liner stops the silicone bulging through the band slots.