Bulk hP High Pressure Lube Filters (3)

Bulk hP high pressure lube filters clean oil as it's pumped from bulk storage to the machine, sitting on the pressure side of an oil dispensing line. They're a Donaldson design built for the higher pressures of pumped oil systems, where a standard low-pressure spin-on isn't suitable. Workshops, fleet depots and mine sites use them to clean hydraulic, transmission, gear and engine oil before it reaches a reservoir or sump. The choice comes down to a micron rating that suits the oil and the component it feeds, and pressure and flow ratings above what your pump delivers. Choose too fine a grade for thick gear oil and fills crawl. Choose too coarse for hydraulic oil and new-oil dirt goes straight into tight-clearance valves. The notes below the products explain where these filters fit.

Bulk hP High Pressure Lube Filters

3 products

  • Donaldson P565185 For Hydraulic – Gear, Transmission and Engine Oil, 8um, 189 Lpm
    Vendor:
    Donaldson

    P565185 for Hydraulic, Gear, Transmission & Engine Oil, 8um, 189 lpm

    Regular price $489.30 AUD
    Sale price $489.30 AUD Regular price
  • Donaldson P565184 For Hydraulic – Gear, Transmission and Engine Oil, 4um, 189 Lpm
    Vendor:
    Donaldson

    P565184 for Hydraulic, Gear, Transmission & Engine Oil, 4um, 189 lpm

    Regular price $487.70 AUD
    Sale price $487.70 AUD Regular price
  • Donaldson P565183 For Hydraulic – Gear, Transmission and Engine Oil, 14um, 189 Lpm
    Vendor:
    Donaldson

    P565183 for Hydraulic, Gear, Transmission & Engine Oil, 14um, 189 lpm

    Regular price $484.60 AUD
    Sale price $484.60 AUD Regular price

Where does a high pressure lube filter go?

On the outlet side of the oil pump, before the hose reel or dispensing gun. Air operated ratio pumps multiply their air supply pressure, so line pressure can be several times what the compressor delivers, which is why the filter housing needs a high pressure rating. Filtering here means every litre dispensed has been cleaned, whatever the condition of the drum or tank it came from.

Choosing the right micron rating

Match it to the component the oil will protect. Hydraulic systems and transmissions with fine clearances and servo valves benefit from finer filtration. Engine and gear oils are thicker, so a coarser grade keeps flow up and pressure drop down, especially on cold mornings. Where the equipment maker gives an ISO 4406 cleanliness target for the oil, use it to set the grade.

What to check before you buy

Pressure rating is the one people miss.

  • Micron rating suited to the oil and component
  • Maximum working pressure above your pump's stall pressure
  • Rated flow at or above the pump's output
  • Fluid compatibility with every oil you dispense through it
  • A restriction indicator or gauge, so elements are changed on condition rather than guesswork

Pair a filter with air operated and manual oil pumps and oil hose reels, compare portable oil filter carts for polishing, or ask us about your system.

Can I put a standard dispenser filter on an oil hose reel line?

No. Air-operated piston and diaphragm pumps deliver oil at pressures well above the air driving them, to push it through long pipe runs and hose reels. Our Donaldson diesel dispenser kits and Clean Solutions heads are rated to 24.1 bar. Bulk hP filters are rated to 68.9 bar working pressure, with a 20.7 bar element collapse rating and 151.7 bar rated static burst.

Regulate the compressed air to each pump so its output stays below 68.9 bar. Allow for thermal expansion too: Donaldson notes a 5.5°C rise in oil temperature can add 31 bar to the system while the pump is off, so follow the pump maker's relief valve recommendations.

The 4 micron P565184 is listed for hydraulic oil. Is it the right element for my hydraulics?

Usually not. Donaldson recommends ISO 16/14/11 for hydraulic and transmission oil, which is the target the 8 micron P565185 is rated to. The 4 micron P565184 targets ISO 14/13/11; choose it only where the equipment maker calls for that cleaner code. Going finer than the target loads the element faster for no gain.

Do you sell the Bulk hP filter heads?

Not online yet. Donaldson makes two heads for these elements: P566023 without a bypass valve and P566024 with a 3.4 bar bypass valve, both rated to 68.9 bar with SAE-16 O-ring connections and an indicator port. The no-bypass head never lets oil around the element; the bypass head keeps oil flowing when the element is loaded. The heads in our filter heads section are 24.1 bar Clean Solutions heads for DBB elements, so they're not a substitute. Ask us for the hP head you need.

The elements also fit the B.O.S.S Lite P506081 oil cart, which runs a P565183 as standard.