Automatic Lubrication Systems (40)

Automatic lubrication systems deliver small, measured shots of grease to every lube point while the machine works, so pins and bearings are greased on time without anyone crawling underneath with a gun. We stock Graco automatic lubrication pumps plus the divider valves, injectors, power cables and fittings to build and maintain these systems on earthmoving, mining, agricultural, truck and industrial equipment. The deciding factors are system type, number of lube points, reservoir size, supply voltage and whether you need a built-in controller. Match the cable and controller to the pump before you order, or the install stalls on the day the fitter arrives. The guide below explains how each system type works.

Graco 96G278 G3 Hammer chisel paste lubrication pump, left angle view

40 products

  • Graco 114909 GL-1 Grease Injector, Single Line Parallel, 241 bar – right-front view
    Vendor:
    Graco

    114909 GL-1 Grease Injector, Single Line Parallel, 241 bar

    Regular price $207.90 AUD
    Sale price $207.90 AUD Regular price
  • Graco 24X807 GL-1 X Grease Injector, Single Line Parallel, 414 bar – front view
    Vendor:
    Graco

    24X807 GL-1 X Grease Injector, Single Line Parallel, 414 bar

    Regular price $278.40 AUD
    Sale price $278.40 AUD Regular price
  • Graco 24X817 GL-1 XL Grease Injector, Single Line Parallel, 414 bar – front view
    Vendor:
    Graco

    24X817 GL-1 XL Grease Injector, Single Line Parallel, 414 bar

    Regular price $484.00 AUD
    Sale price $484.00 AUD Regular price
  • Graco 25R831 G-Mini 24V Automatic Grease Pump, 2L, No Controller, CPC – right-front view
    Vendor:
    Graco

    25R831 G-Mini 24V Automatic Grease Pump, 2L, No Controller, CPC

    Regular price $1,050.00 AUD
    Sale price $1,050.00 AUD Regular price
  • Graco 25R817 G-Mini 24V Automatic Grease Pump, 1L, Controller, DIN – front view
    Vendor:
    Graco

    25R817 G-Mini 24V Automatic Grease Pump, 1L, Controller, DIN

    Regular price $1,073.10 AUD
    Sale price $1,073.10 AUD Regular price
  • Graco 25R800 G-Mini 24V Automatic Grease Pump, 1L, No Controller, CPC – front view
    Vendor:
    Graco

    25R800 G-Mini 24V Automatic Grease Pump, 1L, No Controller, CPC

    Regular price $946.00 AUD
    Sale price $946.00 AUD Regular price
  • Graco 25R801 G-Mini 24V Automatic Grease Pump, 1L, Controller, CPC – front view
    Vendor:
    Graco

    25R801 G-Mini 24V Automatic Grease Pump, 1L, Controller, CPC

    Regular price $1,193.20 AUD
    Sale price $1,193.20 AUD Regular price
  • Graco 25R804 G-Mini 24V Heated Automatic Grease Pump, 1L, Controller, CPC – front view
    Vendor:
    Graco

    25R804 G-Mini 24V Heated Automatic Grease Pump, 1L, Controller, CPC

    Regular price $1,263.60 AUD
    Sale price $1,263.60 AUD Regular price
  • Graco 25R835 G-Mini 24V Automatic Grease Pump, 2L, No Controller, DIN – right-front view
    Vendor:
    Graco

    25R835 G-Mini 24V Automatic Grease Pump, 2L, No Controller, DIN

    Regular price $1,005.60 AUD
    Sale price $1,005.60 AUD Regular price
  • Graco 25R837 G-Mini 24V Automatic Grease Pump, 2L, Controller, DIN – right-front view
    Vendor:
    Graco

    25R837 G-Mini 24V Automatic Grease Pump, 2L, Controller, DIN

    Regular price $1,224.10 AUD
    Sale price $1,224.10 AUD Regular price
  • Graco 25R807 G-Mini 24V Automatic Grease Pump, 0.5L, No Controller, CPC – front view
    Vendor:
    Graco

    25R807 G-Mini 24V Automatic Grease Pump, 0.5L, No Controller, CPC

    Regular price $937.00 AUD
    Sale price $937.00 AUD Regular price
  • Graco 2003467 5-Wire CPC Power Cable, 4.6 m, for G-Mini Grease Pumps
    Vendor:
    Graco

    2003467 5-Wire CPC Power Cable, 4.6 m, for G-Mini Grease Pumps

    Regular price $242.60 AUD
    Sale price $242.60 AUD Regular price
  • Graco 25R833 G-Mini 24V Automatic Grease Pump, 2L, Controller, CPC – front view
    Vendor:
    Graco

    25R833 G-Mini 24V Automatic Grease Pump, 2L, Controller, CPC

    Regular price $1,270.50 AUD
    Sale price $1,270.50 AUD Regular price
  • Graco 2003896 5-Wire CPC Power Cable, 9.1 m, for G-Mini Grease Pumps
    Vendor:
    Graco

    2003896 5-Wire CPC Power Cable, 9.1 m, for G-Mini Grease Pumps

    Regular price $449.30 AUD
    Sale price $449.30 AUD Regular price
  • Graco 127783 2-Wire CPC Power Cable, 4.6 m, for G-Mini No-Controller Pumps
    Vendor:
    Graco

    127783 2-Wire CPC Power Cable, 4.6 m, for G-Mini No-Controller Pumps

    Regular price $190.60 AUD
    Sale price $190.60 AUD Regular price

How does automatic lubrication work?

A pump with a grease reservoir runs on a timer or machine signal and sends grease through a distribution network to each point. The three common layouts handle that distribution differently.

  • Progressive (divider valve) systems: the pump feeds a series progressive divider valve whose pistons cycle in a fixed sequence, sending grease to each outlet in turn. If one point blocks, the whole valve stops, which makes faults easy to detect with a cycle indicator or sensor.
  • Injector systems: the pump pressurises a single supply line, then vents. Each point has its own injector, and adjustable injectors let different points get different amounts from the same line.
  • Pump-to-point systems: each pump element feeds one lube point directly, with no divider valves. They suit machines with a small number of critical points.

Choosing a system

  • Number and location of lube points, and how far apart they are.
  • Grease grade: check the pump and system are rated for the NLGI grade you run, especially in cold weather.
  • Reservoir size against how often someone can refill it.
  • Supply voltage and the matching power cable and connector.
  • Controller: built-in timer and low-level alarm, or control from the machine.

Can I add points to an existing system?

Often, yes, but the method depends on the layout. Progressive systems need the divider valve resized or another section added, while injector systems take extra injectors on the supply line. Check the pump's output can keep up with the extra demand, and refer to the Graco installation manual for your pump.

Send us the machine and lube point count and we'll help work out the parts. For manual greasing, see grease guns or browse all grease equipment.

Which Graco pump family suits my machine?

Choose the family by how the grease needs to reach the lube points. All three run on 24 VDC.

  • G-Mini: compact pump with a 0.5L to 4L reservoir, delivering 3 cm³ per minute at up to 280 bar into series progressive divider valves or pump-to-point lines.
  • G3: 2L to 12L reservoir with one to three pump elements, each delivering up to 4 cm³ per minute at up to 351.6 bar, usually feeding divider valves or injectors.
  • G5: five pump elements fitted for pump-to-point lubrication, each feeding one lube point directly at up to 293 bar and 2.54 cm³ per minute, without divider valves. All are 4L with a 5-pin CPC connector: the 95G101 (standard orientation) and 95G103 (vertical) are switched by your PLC or lube timer, and the 95G104 Pro has a built-in timer with alarm relay.

Cold starts: unheated G-Mini 0.5L, 1L and 2L models are rated down to -15°C, and the 25R804 has a heater that keeps NLGI #2 grease pumping to -40°C. G3 Standard, Hammer and Pro pumps are rated -40°C to 70°C ambient, and the Max Gen 2 and HF Max -30°C to 70°C. The grease must suit the temperature too.

The next two questions list the G-Mini and G3 models we stock.

Which G-Mini model do I need?

Choose by three things: whether your machine already has a PLC or lube timer to switch the pump, which power plug your wiring uses (CPC or DIN), and how much grease the reservoir needs to hold. Every model runs on 24 VDC and delivers 3 cm³ of grease per minute at up to 280 bar.

No controller: your PLC or lube timer switches the pump

With controller: the pump times each lube run in minutes or divider-valve cycles and alarms when grease runs low

  • 25R801: 1L, CPC plug, follower plate
  • 25R804: 1L, CPC plug, follower plate, heater for use down to -40°C
  • 25R833: 2L, CPC plug
  • 25R911: 4L, CPC plug
  • 25R817: 1L, DIN plug
  • 25R837: 2L, DIN plug

Size the reservoir so it empties about once a month. Every pump also needs a power cable and a divider valve, both ordered separately.

Which G3 model do I need?

Choose by how the pump will be controlled, then by reservoir size. Size the reservoir so it lasts a sensible refill interval for your machine.

No controller: your PLC or lube timer switches the pump

  • 96G005: 2L, CPC, M12 low-level output
  • 96G048: 4L, CPC, M12 low-level output
  • 96G049: 8L, CPC, M12 low-level output
  • 96G199: 12L, CPC, M12 low-level output
  • 96G278: 4L Hammer pump for chisel paste, 5-wire CPC

G3 Pro: built-in timer for divider valve systems

  • 96G149: 4L, 5-pin CPC
  • 96G150: 8L, 5-pin CPC
  • 96G068: 4L, CPC, M12 remote run
  • 96G069: 8L, CPC, M12 remote run
  • 96G073: 4L, follower plate, CPC, M12 remote run

G3 Max Gen 2: LCD controller for injector or divider valve systems

G3 HF Max: high flow for injector systems on larger machines

  • 96G619: 8L, pressure transducer, 24.6 cm³/min

Does the pump come with a power cable?

G-Mini: no. Every G-Mini needs a power cable, ordered separately:

  • CPC pumps: the 5-wire 2003467 (4.6 m) or 2003896 (9.1 m), which carry power plus the low-level signal or manual run button wiring.
  • No-controller CPC pumps that do not need the low-level signal: the 2-wire 127783 (4.6 m).
  • DIN pumps: the 16U790 DIN power cable (4.6 m).

G3: yes. The CPC models with a 2-pin plug (96G005, 96G048, 96G049, 96G199, 96G068, 96G069, 96G073, 96G548, 96G552 and 96G619) ship with a 4.5 m 2-wire CPC cable. The 96G149 and 96G150 ship with a 5-wire CPC cable, which connects the 571031 illuminated remote run button, and the 96G278 Hammer ships with a 5-wire cable that carries its low-level signal. Max Gen 2 and HF Max pumps take the 7-wire 2001714 cable for a 25C982 remote run button and alarm outputs.

G5: yes. Each model ships with a CPC power cable. On the 95G104 the 5-wire cable also connects the 571031 illuminated remote run button.

What else does the installation need?

Graco requires three things alongside every pump: a fuse in the 24 VDC supply, a pressure relief valve close to every pump outlet, and grounding.

G-Mini: 5A fuse kit 26C917 for the no-controller pumps, 7.5A kit 571039 for the controller pumps (Graco's fuse table does not yet list the 4L models, so ask us for those), and the adjustable relief valve kit 571028. The 26C956 hose kit runs from the relief valve outlet (1/4" NPT) to a CSP valve inlet (1/8" NPT), and the 2016002 bracket is made for the 4L pumps.

G3: the 4 A fuse kit 571040 for Standard, Hammer and Pro pumps, or the 7.5 A kit 25C986 for Max Gen 2 and HF Max pumps. The adjustable 571028 return-to-reservoir relief kit (571071 for BSPP) suits Standard, Hammer, Pro and Max Gen 2 pumps; the HF Max manual lists valve 132265. The 125910 bracket mounts the G3 base (the HF Max uses the 2012024 L-bracket), and extra 571041 pump elements add outlets.

G5: the 4 A fuse kit 571040. G5 relief valves are the 133910 (276 bar), the 133991 set of five, or the 133958 kit of five valves with a return to the reservoir. Volume spacers are sold separately as kit 133457.

Outlet fittings: every G-Mini, G3 and G5 outlet is 1/4-18 NPSF female and takes 1/4-18 NPT male fittings. BSP fittings will not seal in it.

Parts shown without a link are available on request.

Which divider valve or injector do I need?

Divider valves (series progressive)

A series progressive divider valve splits the pump's output into measured shots, one lube point per outlet. Choose by the number of points. G3 Standard, Pro, Max Gen 2 and Hammer pumps ship with one pump element and take up to three, each feeding its own valve or injector circuit at 4 cm³ per minute with no spacers (3 with one, 2 with two).

Each outlet delivers 0.2 cm³ per stroke, and a 17L651 plug combines two outlets for a point that needs more. The valves have a 1/8" NPT inlet and are rated to 350 bar. Outlet fittings and tubing are sold separately, and Graco requires CSP outlet fittings with a clamping ring.

Injectors (single line parallel)

Injector systems need a normally open vent valve to reset the injectors after each lube event. The G3 Max Gen 2 (96G548, 96G552) and HF Max (96G619) controllers drive that valve directly. Standard G3 pumps can feed injectors when the machine's controller runs a separate vent valve. The G3 Pro manual covers series progressive divider valve systems. The G-Mini suits series progressive divider valves or pump-to-point lines, not single line parallel injector systems such as the GL-1.

GL-1 injectors we stock: 114909 (241 bar), 24X807 and 24X817 (414 bar).

These are grease pumps for NLGI 000 to #2 grease; Graco makes separate G-Mini oil pumps.

How is a G-Mini reservoir refilled?

Grease models fill through the Zerk inlet fitting on the pump. For faster filling, add the 24M644 fill stud with its 121474 coupler (Graco's recommended accessory for the 4L pumps), or the 2006597 cartridge filler with its 2000200 adapter for 400 g cartridges. These parts are available on request.