In-line Fuel Filters (83)

In-line fuel filters sit directly in the fuel line between tank and engine, either as the main filter on smaller engines or as extra protection ahead of a lift pump, carburettor or injection system. They're common on mowers, small machinery, generators, older vehicles and auxiliary fuel setups, in metal and plastic bodies with barbed or threaded ends. Hose size at both ends decides the fit, followed by the pressure the line runs at. An undersized filter, or one with media too fine for a low-pressure line, starves the engine, which shows up as surging or stalling under load. Check the sizing notes below before ordering.

In-line Fuel Filters

83 products

  • Baldwin BF7725 Fuel Filter – In-Line, Plastic, Nylon, 5/16 In-out
    Vendor:
    Baldwin

    BF7725 Fuel Filter- In-Line, Plastic, Nylon, 5/16 in-out

    Regular price $10.00 AUD
    Sale price $10.00 AUD Regular price
  • Baldwin BF833-K2 Fuel Filter – In-line, Metal, 1/4 In-out, Clamps and Hoses
    Vendor:
    Baldwin

    BF833-K2 Fuel Filter- In-line, Metal, 1/4 in-out, Clamps & Hoses

    2 in stock
    Regular price $13.50 AUD
    Sale price $13.50 AUD Regular price
  • Baldwin BF1123 Fuel Filter – In-line, Metal, 5/16 In-out
    Vendor:
    Baldwin

    BF1123 Fuel Filter- In-line, Metal, 5/16 in-out

    Regular price $19.50 AUD
    Sale price $19.50 AUD Regular price
  • Fleetguard FF149 Fuel Filter – In-line, Metal, 5/16 In-out
    Vendor:
    Fleetguard

    FF149 Fuel Filter- In-line, Metal, 5/16 in-out

    7 in stock
    Regular price $12.20 AUD
    Sale price $12.20 AUD Regular price
  • Baldwin BF836-K3 Fuel Filter – In-line, Metal, 3/8 In-out, Clamps and Hoses
    Vendor:
    Baldwin

    BF836-K3 Fuel Filter- In-line, Metal, 3/8 in-out, Clamps & Hoses

    3 in stock
    Regular price $22.50 AUD
    Sale price $22.50 AUD Regular price
  • Baldwin BF7693 Fuel Filter – In-Line, Metal, Steel Screen, 1/2 In-out
    Vendor:
    Baldwin

    BF7693 Fuel Filter- In-Line, Metal, Steel Screen, 1/2 in-out

    Regular price $25.50 AUD
    Sale price $25.50 AUD Regular price
  • Baldwin BF1052 Fuel Filter – In-line, Metal, 3/8 In-out
    Vendor:
    Baldwin

    BF1052 Fuel Filter- In-line, Metal, 3/8 in-out

    Regular price $24.00 AUD
    Sale price $24.00 AUD Regular price
  • Fleetguard FF157 Fuel Filter – In-line, Metal, 3/8 In-out, Clamps and Hoses
    Vendor:
    Fleetguard

    FF157 Fuel Filter- In-line, Metal, 3/8 in-out, Clamps & Hoses

    2 in stock
    Regular price $29.30 AUD
    Sale price $29.30 AUD Regular price
  • Baldwin BF9884 Fuel Filter – In-line, Plastic, Nylon, 5/16 In-out
    Vendor:
    Baldwin

    BF9884 Fuel Filter- In-line, Plastic, Nylon, 5/16 in-out

    2 in stock
    Regular price $13.50 AUD
    Sale price $13.50 AUD Regular price
  • Baldwin BF840-K1 Fuel Filter – In-line, Metal, 5/16 In-out, Clamps and Hoses
    Vendor:
    Baldwin

    BF840-K1 Fuel Filter- In-line, Metal, 5/16 in-out, Clamps & Hoses

    6 in stock
    Regular price $13.50 AUD
    Sale price $13.50 AUD Regular price
  • Baldwin BF1049 Fuel Filter – In-line, Metal, 5/16 In-out
    Vendor:
    Baldwin

    BF1049 Fuel Filter- In-line, Metal, 5/16 in-out

    Regular price $14.60 AUD
    Sale price $14.60 AUD Regular price
  • Donaldson P550902 in-line fuel filter with white plastic housing and 6mm inlet and outlet connections
    Vendor:
    Donaldson

    P550902 Fuel Filter, In-Line

    Regular price $30.50 AUD
    Sale price $30.50 AUD Regular price
  • Sakura FS-28150 fuel filter, a black cylindrical automotive part with Ryco Z590 branding
    Vendor:
    Sakura

    FS-28150 Fuel Filter

    Regular price $26.90 AUD
    Sale price $26.90 AUD Regular price
  • Sakura FS-44500 in-line metal fuel filter with black protective end caps on a white background
    Vendor:
    Sakura

    FS-44500 Fuel Filter- In-line, Metal

    Regular price $35.80 AUD
    Sale price $35.80 AUD Regular price
  • Sakura FS-26180 Fuel Filter – In-line, Metal
    Vendor:
    Sakura

    FS-26180 Fuel Filter- In-line, Metal

    Regular price $123.10 AUD
    Sale price $123.10 AUD Regular price

How do I size an in-line fuel filter?

Measure the inside diameter of the hose at both ends, as some filters step down from inlet to outlet.

  • Imperial or metric: 5/16 inch and 8 mm are close but not the same, and a loose fit on a barb leaks fuel or draws air.
  • Barb or thread: threaded ends connect straight to fittings, while barbed ends need the right hose and clamps.
  • Body material: plastic bodies suit low-pressure carburettor and gravity-fed lines. Fuel-injected systems need a filter rated for the system pressure, usually metal-bodied.
  • Media: wire mesh units are coarse screens for catching debris, not fine filters.
  • Fuel type: check the filter is rated for petrol, diesel or ethanol blends as needed.

Which way does an in-line filter go?

Follow the arrow on the body, which points toward the engine. Fitted backwards, the filter can restrict flow or push trapped dirt downstream.

Where should it be fitted?

Mount it where it's easy to see and reach, clear of exhaust heat and moving parts, and support the line so the filter doesn't hang off the hose. Clear-bodied filters make it easy to spot dirt or water at a glance.

Bigger diesel systems need spin-on fuel filters or a spin-on fuel water separator, and glass and plastic bowl units sit in fuel filter bowls and assemblies. Contact us if you need help matching a line size.

How do I choose the right in-line fuel filter?

Match the connections first, then the element type, then the job it has to do.

  • Connections: imperial hose sizes run from 3/16 in to 1/2 in, and Sakura's in-line filters add metric hose sizes from 6 mm to 10 mm. Some filters step between sizes, such as the BF7736-K1 at 5/16 in inlet and 1/4 in outlet, or the FS-7909 at 6 mm in and 8 mm out. Threaded versions use metric fittings such as M12 x 1.25 and M14 x 1.5.
  • Element: a filter element, or a wire or nylon mesh screen for coarse straining.
  • Job: a strainer ahead of a pump, a filter on a small engine, or a filter with a water drain.

Measure the hose bore rather than guessing. The table below lists our Baldwin and Fleetguard in-line filters by connection size; for Sakura's, check the size on the product page.

Are there in-line fuel filters that separate water?

Yes. Two Baldwin in-line filters have a water drain: the BF7965 with a 5/16 in inlet and 3/8 in outlet, and the BF9881 with 3/8 in connections. They suit a small engine or a line where a full separator won't fit. For a dedicated separator with more options, such as a bowl or water-in-fuel sensor, see spin-on fuel/water separators.

Do in-line fuel filters come with hoses and clamps?

Some do. Baldwin's -K suffix marks a kit with fittings:

Threaded filters come with sealing washers: four copper washers with the BF885, four metal washers with the BF1100. Check the table below for what comes with each Baldwin and Fleetguard filter, and the product page for the rest.

Can an in-line filter be the main fuel filter on a common-rail engine?

No. Common-rail engines need their specified primary and secondary filters, with the secondary at the fine rating the injection system demands, currently 4–5 micron at 99.9% on new designs. An in-line filter or mesh strainer can protect a lift pump or catch debris in a line, but it replaces neither. If you want more protection ahead of the engine's own filters, look at the add-on kits in filter kits for diesel and common-rail engines.

Which way round does an in-line fuel filter go?

With the flow arrow pointing toward the engine. Check the body for the arrow before you cut or clamp anything. Where a filter has more than two connections, such as the BF7756 with its 13/32 in return line, label the hoses before you take the old filter off so each one goes back to the right port.