Exhaust Flex Tubing (3)

Exhaust flex tubing is flexible stainless steel tube fitted into an exhaust system where it needs to move, taking up engine vibration, rocking on the mounts and heat expansion that would otherwise crack rigid pipe, muffler connections or the turbo outlet. It's used on trucks, tractors, gensets and off-highway machines, usually between the engine and a frame- or cab-mounted muffler or stack. Most is sold in lengths to be cut to fit, listed by inside diameter so it slides over the exhaust pipe. Measure the pipe outside diameter, allow enough overlap at each end for a clamp, and avoid using flex to bridge a big misalignment. A cracked flex leaks exhaust fumes, and on a truck or tractor those can find their way into the cab.

Exhaust Flex Tubing

3 products

  • Donaldson J034673 Stainless Exhaust Flex Tube, 102 mm / 4 in ID x 914 mm / 36 in, Cut to Length
    Vendor:
    Donaldson

    J034673 Stainless Exhaust Flex Tube, 102 mm / 4 in ID x 914 mm / 36 in, Cut to Length

    Regular price $169.90 AUD
    Sale price $169.90 AUD Regular price
  • Donaldson J034674 Stainless Exhaust Flex Tube, 127 mm / 5 in ID x 914 mm / 36 in, Cut to Length
    Vendor:
    Donaldson

    J034674 Stainless Exhaust Flex Tube, 127 mm / 5 in ID x 914 mm / 36 in, Cut to Length

    Regular price $195.70 AUD
    Sale price $195.70 AUD Regular price
  • Donaldson J024850 Stainless Exhaust Flex Tube, 89 mm / 3.5 in ID x 610 mm / 24 in, Cut to Length
    Vendor:
    Donaldson

    J024850 Stainless Exhaust Flex Tube, 89 mm / 3.5 in ID x 610 mm / 24 in, Cut to Length

    Regular price $107.50 AUD
    Sale price $107.50 AUD Regular price

Why does an exhaust need flex tubing?

Because the engine and exhaust don't move together. The engine rocks on rubber mounts while the muffler and stack are fixed to the frame or cab, and the pipe grows as it heats. A short length of flex absorbs that movement so welds, brackets and muffler joints don't take it.

How do I cut and fit exhaust flex?

Measure the gap, add overlap for each pipe end, then cut cleanly with an abrasive disc or fine-tooth blade. Wrapping tape or fitting a clamp either side of the cut first stops the windings unravelling. Slide it over the pipe and clamp each end with a seal clamp of the right size.

How long should the flex section be?

Long enough to absorb the movement without being stretched, compressed or bent hard. Flex installed under strain or used to make a sharp bend fails early. Follow the engine or equipment maker's guidance where they specify a length.

  • Pipe outside diameter
  • Inside diameter of the flex
  • Length needed plus clamp overlap
  • Material and temperature rating
  • Clamp style: stepped or flat band seal clamp

Clamp both ends with exhaust seal clamps, keep rain out of the stack with rain caps, browse all air intake and exhaust parts, or ask us to size a flex.

Which flex tube fits my exhaust pipe?

Pick by the outside diameter of the exhaust pipe: the tube's bore slides over it.

  • 89 mm (3.5 in) pipe: J024850, 610 mm long.
  • 102 mm (4 in) pipe: J034673, 914 mm long.
  • 127 mm (5 in) pipe: J034674, 914 mm long.

Those lengths are measured fully extended, and you cut the tube to suit. Allow for the overlap at each end when you cut it, so the clamps have pipe and flex to grip together. Replacing a Walker, Stemco or Dynaflex tube? The cross reference tab on each listing carries those numbers.

Which clamp goes on exhaust flex tube?

A stepped SealClamp at each end, sized to the pipe: X007831 for the 89 mm tube, X007784 for 102 mm and X007785 for 127 mm. That's two clamps for each length of flex you fit.

Donaldson specifies the stepped clamp for each of these tubes because its stepped band grips the flex and the pipe together without pinching the flex. A U-bolt grips at one point and can crush the pipe out of round, leaving gaps for soot and fumes. The tightening figure is on the clamp listing.