Fuel Filters & Water Separators (938)

Fuel filters and water separators stop dirt and water from reaching the injection pump and injectors on diesel trucks, tractors, earthmovers, gensets and boats. High-pressure common-rail systems run very tight clearances, so the fuel filter is the main defence for some of the most expensive parts on the engine. Most diesels use a staged setup: a coarser primary filter, often with water separation, ahead of a finer secondary. The micron rating and the filter's position in that sequence decide the pick. Fit the wrong one and it still seals and the engine still starts, while fine particles or free water quietly wear the injectors. Choose your filter format from the guide below the products.

Fuel Filters & Water Separators

938 products

  • Fleetguard FF167A Fuel Filter – Can Type, Rolled Paper
    Vendor:
    Fleetguard

    FF167A Fuel Filter- Can Type, Rolled Paper

    Regular price $8.50 AUD
    Sale price $8.50 AUD Regular price
  • Baldwin BF825 Fuel Filter – Can Type
    Vendor:
    Baldwin

    BF825 Fuel Filter- Can Type

    Regular price $9.00 AUD
    Sale price $9.00 AUD Regular price
  • Racor PFF5510 Spin-On Fuel/ Water Separator – 10um, Inboard and Outboard Petrol Applications
    Vendor:
    Racor

    PFF5510 Spin-On Fuel Water Separator, 10um, suits Mercury, Mercruiser, Yamaha, Suzuki, Honda and Tohatsu Inboard & Outboard Applications

    3 in stock
    Regular price $34.00 AUD
    Sale price $34.00 AUD Regular price
  • Baldwin BF790 Fuel Filter – Spin-on
    Vendor:
    Baldwin

    BF790 Fuel Filter- Spin-on

    1 in stock
    Regular price $25.50 AUD
    Sale price $25.50 AUD Regular price
  • Baldwin BF7608 Fuel Filter – Spin-on
    Vendor:
    Baldwin

    BF7608 Fuel Filter- Spin-on

    Regular price $25.50 AUD
    Sale price $25.50 AUD Regular price
  • Fleetguard FF5114 Fuel Filter – Spin-on, 20 micron
    Vendor:
    Fleetguard

    FF5114 Fuel Filter- Spin-on, 20 Mic

    4 in stock
    Regular price $14.60 AUD
    Sale price $14.60 AUD Regular price
  • Baldwin PF7698 Fuel Filter – Cartridge, Lid
    Vendor:
    Baldwin

    PF7698 Fuel Filter- Element, Lid

    Regular price $66.00 AUD
    Sale price $66.00 AUD Regular price
  • Fleetguard FF5040 Fuel Filter – Spin-on
    Vendor:
    Fleetguard

    FF5040 Fuel Filter- Spin-on

    4 in stock
    Regular price $23.00 AUD
    Sale price $23.00 AUD Regular price
  • Baldwin PF10 Fuel Filter – Cartridge, Fuel Storage
    Vendor:
    Baldwin

    PF10 Fuel Filter- Element, Fuel Storage

    Regular price $31.50 AUD
    Sale price $31.50 AUD Regular price
  • Baldwin BF940 Fuel Filter – Spin-on
    Vendor:
    Baldwin

    BF940 Fuel Filter- Spin-on

    6 in stock
    Regular price $21.00 AUD
    Sale price $21.00 AUD Regular price
  • Fleetguard FF5229 Fuel Filter – Spin-on
    Vendor:
    Fleetguard

    FF5229 Fuel Filter- Spin-on

    2 in stock
    Regular price $22.70 AUD
    Sale price $22.70 AUD Regular price
  • Baldwin PF872 Fuel Filter – Cartridge
    Vendor:
    Baldwin

    PF872 Fuel Filter- Element

    Regular price $10.00 AUD
    Sale price $10.00 AUD Regular price
  • Baldwin BF7725 Fuel Filter – In-Line, Plastic, Nylon, 5/16 In-out
    Vendor:
    Baldwin

    BF7725 Fuel Filter- In-Line, Plastic, Nylon, 5/16 in-out

    Regular price $10.00 AUD
    Sale price $10.00 AUD Regular price
  • Baldwin BF988 Fuel Filter – Spin-on
    Vendor:
    Baldwin

    BF988 Fuel Filter- Spin-on

    Regular price $18.00 AUD
    Sale price $18.00 AUD Regular price
  • Baldwin BF1267 Fuel/ Water Separator – Spin-on, Drain
    Vendor:
    Baldwin

    BF1267 Fuel/ Water Separator, Spin-on, Drain

    2 in stock
    Regular price $54.00 AUD
    Sale price $54.00 AUD Regular price

Which type of fuel filter does my engine use?

Look at what's on the engine now, then go to the matching collection.

Primary vs secondary fuel filters

The primary takes out water and larger particles, and the secondary does the fine filtration that protects the injection system. Primaries usually carry a coarser micron rating than secondaries. Swap them over and the fine filter blocks early while the injectors lose their last layer of protection.

Why does water in diesel matter?

Water causes corrosion, strips lubrication from pump and injector parts, and lets microbial growth take hold in tanks. A separator only works if it gets drained, so check the bowl or drain at every service, and more often in humid weather or after filling from an unfamiliar tank.

The FAQ below answers common questions. Doing a full service? See 4WD and truck filter kits or HPCR diesel filter kits, and treat contaminated tanks with fuel treatments and biocides. Ask us if you're unsure which filter goes where.

Which type of fuel filter do I need: spin-on, separator, cartridge, in-line or box style?

Replace like with like. The filter head or housing on the engine sets the format, so start with what comes off the machine, then match the rating to the position the filter sits in.

Donaldson engine fuel filter kits are also in this section, such as the P551124 for John Deere 6090H and 6068 engines and the X770914 for Scania DC9, DC13 and DC16. Running a boat? Our Racor units and elements are in marine fuel filters.

What fuel filter rating does a common-rail diesel need?

The rating your engine maker specifies for each position, at the efficiency they specify. Never fit a coarser or lower-efficiency filter because it's the one on the shelf.

Common-rail pumps and injectors run at roughly 2,000–3,100 bar with very tight clearances, and the on-engine filter is the last chance to stop contaminant reaching them. That's why our listings quote efficiency at a size where the maker publishes it, such as 98.7% at 13.7 micron on the FF2200, so you can check a replacement against the spec and not just the title.

Typical ratings by position, for current and older fuel systems, are in the table below.

Do I need both a primary and a secondary fuel filter?

If your engine was built with both, yes. They do different jobs, and each position needs the filter built for it.

The primary sits on the suction side ahead of the transfer pump and is sized for capacity and water removal. The secondary sits after the pump, works under pressure and does the fine filtration that protects the injection pump and injectors. Without an effective primary, dirt and water reach the transfer pump and the on-engine filtration can be overwhelmed. Without the right secondary, the injection system gets less protection than it was designed for. Donaldson notes the primary has only about 34–41 kPa (5–6 psi) of suction to work with, so it has to be low-restriction, and typically carries a nominal 10–30 micron rating. The secondary sees much higher pressure after the pump and is typically 4–10 micron nominal. Typical ratings for each position are in the table below.

Can I run biodiesel blends through these filters?

Check the listing for the specific filter, because fuel compatibility is set by each maker and we won't give a blanket answer. Where the maker publishes it, we show it: Racor's 320R-RAC-01, for example, is listed for diesel, biodiesel and petrol engines.

What blends change, whichever filter you run:

  • Biodiesel has a greater affinity for water, which makes water separation harder.
  • It supports more aggressive microbial growth, so expect more sludge in tanks and filters.
  • It can hit cold-weather problems sooner than straight diesel.

On blended fuel, watch separator drains and filter life closely. If a listing doesn't state compatibility for the blend you run, send us the part number and the blend and we'll check it with the maker.

Why do my fuel filters keep blocking early?

Usually because of what's in the fuel, not the filter. Fleetguard name organic sludge, from fuel degradation and additive interactions, as the most common cause of plugged filters.

  • Water and microbes: water condenses in tanks during storage, and microbes grow at the fuel-water boundary, forming sludge that blocks filters and acids that corrode tanks.
  • Particles: dust, dirt, rust and debris picked up in transfer and storage.
  • Oxidised fuel: all diesel carries some asphaltene, a by-product of fuel oxidising. Donaldson puts the particles at about 0.5–2 micron: soft and harmless to the injection system, but they stick to the media. A black, tarry layer on the dirty side of a choked filter is asphaltene, which points to old or oxidised fuel rather than a faulty filter.
  • Wax: depending on fuel quality, paraffin crystals can form anywhere from about -17 °C to 7 °C and coat the media. A water-logged primary element is especially prone to waxing.

If blocking follows deliveries or a particular tank, sample the tank bottom and fix the source. Our fuel treatments and biocides cover diesel bug, and bulk fuel and lube filtration cleans fuel at the tank.

How often should I change fuel filters?

At the interval in your engine or equipment manual, and sooner if the fuel tells you to. We don't publish a blanket figure because intervals vary by engine, fuel system and duty.

Change early when:

  • Restriction rises, or the engine loses power or starts hard soon after a fuel delivery.
  • The separator is collecting water faster than usual.
  • The machine is filled from on-site tanks of uncertain condition.

Drain separators as the manual specifies and whenever the water-in-fuel warning comes on, not only at filter changes. A filter that blocks well before its interval is telling you about the fuel, so look at the tank as well as the filter.