API Service Classifications for Engine Oils: SN to SQ
The API category on an oil's label determines whether it meets OEM warranty requirements, not just whether it is the right viscosity. This guide covers the current petrol (SQ, SP, SN) and diesel (CK-4, CJ-4) categories, how to read the label, and where ACEA and OEM-specific standards fit alongside API.
API service classifications, set by the American Petroleum Institute, define the minimum performance an engine oil must meet for a given engine type and generation. The classification on the label determines whether an oil meets OEM warranty requirements, not just whether it is the correct viscosity. Specifying an oil below the category an engine requires leaves it unprotected against the specific wear, deposit, or oxidation risks that category was designed to address, and can void OEM warranty cover.
This guide covers how the API system is structured, how to read the category and viscosity grade on an oil label, and the current categories for petrol and diesel engines, including the newly introduced API SQ. It also covers how petrol and diesel oils differ chemically, and where API classifications sit alongside ACEA and OEM-specific standards.
What API Service Classifications Are
API service classifications are performance standards, not marketing terms. They confirm what an oil has been tested to do under defined conditions: control wear, resist oxidation, limit deposit formation, and in diesel applications, manage soot loading.
The system is split into two families. “S” (Service) categories apply to petrol engines. “C” (Commercial) categories apply to diesel engines. Within each family, categories are sequential: API SQ is the current petrol category, having succeeded API SP from 31 March 2025, and API CK-4 remains the current heavy-duty diesel category. Each new category supersedes the last by tightening the test limits an oil must pass, typically in response to new engine hardware, such as turbocharged direct injection or diesel particulate filters, or new failure modes identified in the field.
Newer API categories are backward compatible: an API SQ oil can be used in an engine that specifies API SP, SN, or earlier. The reverse does not apply. An oil rated to an older category should not be used where the manufacturer specifies a newer one, because it has not been tested against that category’s requirements.
Reading the API Marks
Every oil label states two things a buyer needs to check: the service category and the SAE viscosity grade. Not all brands present this information the same way on pack, so read the printed text directly rather than relying on a particular symbol or layout.
The service category is printed on the label, for example API SQ or API CK-4, and confirms what the oil has been tested to do for that engine type. The SAE viscosity grade, for example 10W-30, is printed alongside it: the “W” denotes the oil’s cold-cranking (winter) viscosity rating, and the second number its viscosity at normal operating temperature. Together, the grade describes how the oil’s flow resistance changes across that temperature range. Some labels also note Resource Conserving or Energy Conserving compliance, indicating the oil meets API’s fuel economy criteria.
The API Certification Mark, also called the Starburst, appears only on oils that have passed the full current-category test sequence for petrol engines. Its presence confirms current-category compliance, but not every licensed oil displays it, so its absence does not necessarily mean an oil is non-compliant. Where the mark is not shown, check the printed category and viscosity grade directly, or confirm licensing through API’s EOLCS directory (see below).
When cross-referencing an oil against an engine’s specification sheet, match the category first, then confirm the viscosity grade against the OEM’s stated range for the expected ambient operating temperature.
API Categories at a Glance
The current and previous petrol (S) and diesel (C) categories, for quick reference before the detail below.
| Category | Year | Key Protection Added |
|---|---|---|
| Petrol engines — “S” categories | ||
| API SQ | 2025 | Current category. Builds on SP: tighter high/low-temperature deposit and fuel-economy tests, 0.9% sulfated ash limit for GPF protection, enables 0W-8/0W-12 ultra-low viscosity grades |
| API SP | 2020 | Predecessor to SQ, still valid. LSPI protection; tightened wear and high-temperature deposit limits |
| API SN Plus | Supplement to SN | LSPI protection for turbocharged direct-injection (TGDI) engines |
| API SN | 2010 | High-temperature deposit control, sludge control, seal compatibility |
| API SM | 2004 | Oxidation stability, anti-wear performance, low-temperature flow |
| API SL & earlier | Pre-2004 | Baseline protection for older engines only; does not meet current LSPI or deposit requirements |
| Diesel engines — “C” categories | ||
| API CK-4 | 2016 | Improved resistance to oxidation, shear and soot-related wear |
| API CJ-4 | 2006 | DPF/SCR compatible; low-SAPS chemistry |
| API CI-4 | 2002 | EGR compatible; targets soot-related viscosity increase |
| API CH-4 & earlier | Pre-2002 | Baseline protection for older engines only; not tested for after-treatment compatibility |
Scroll the table sideways on a phone to see the full protection column.
API Categories for Petrol Engines
API SQ (2025)
The current category, in effect since 31 March 2025 and first announced at API’s Lubricants Group meeting in June 2024. It builds on SP with tightened high-temperature deposit and viscosity-increase testing (Sequence IIH), improved low-temperature deposit control (Sequence VH), and a greater fuel-economy credit (Sequence VI). SQ sets a maximum sulfated ash limit of 0.9%, and is the first category to support ultra-low viscosity grades such as SAE 0W-8 and 0W-12. Backward compatible with SP and all earlier “S” categories.
API SP (2020)
Superseded by SQ but still a valid, current specification. Added LSPI protection for turbocharged direct-injection engines, alongside tightened wear and high-temperature deposit limits over SN. Backward compatible with all earlier “S” categories.
API SN Plus
A supplement to SN adding LSPI protection, relevant to turbocharged petrol direct-injection (TGDI) engines built before SP existed.
API SN (2010)
High-temperature piston deposit control, sludge control, and seal compatibility, suitable across current and earlier petrol engines.
API SM (2004)
Improved oxidation stability, anti-wear performance, and low-temperature flow over SL.
API SL and earlier
Adequate for the engines they were developed for, but do not meet current wear, deposit, or LSPI protection requirements. Using these in an engine that specifies SN or SP is a warranty and protection risk, not only a performance shortfall.
Why the SQ Ash Limit Matters for GPF-Equipped Engines
SQ’s sulfated ash limit matters most for engines fitted with a gasoline particulate filter (GPF), now common on turbocharged direct-injection petrol models. Ash residue from oil additives is a leading cause of GPF clogging, and the 0.9% ceiling reduces that risk, protecting emission system service life. SQ was released alongside the related ILSAC GF-7 standard; the two are closely aligned, though SQ additionally covers the ultra-low viscosity grades that GF-7 does not.
Why LSPI Protection Matters for TGDI Engines
LSPI matters specifically for turbocharged, direct-injection petrol engines, where fuel droplets can ignite ahead of the spark event and generate pressure spikes capable of damaging pistons and connecting rods. For TGDI engines, confirm SN Plus, SP, or SQ compliance rather than assuming any current-looking oil is suitable.
API Categories for Diesel Engines
API CK-4 (2016)
Current heavy-duty category. Improved resistance to oxidation, shear, and soot-related wear over CJ-4, formulated for both current and older high-speed four-stroke diesel engines.
API CJ-4 (2006)
Developed for engines fitted with diesel particulate filters (DPF) and selective catalytic reduction (SCR), with the low-SAPS chemistry those after-treatment systems require.
API CI-4 (2002)
Developed for engines with exhaust gas recirculation (EGR), targeting soot-related viscosity increase and wear.
API CH-4 and earlier (pre-2000 engine designs)
Adequate protection for the engines they were developed for, but not tested against the soot-handling or after-treatment compatibility requirements newer engines depend on.
Where After-Treatment Hardware Changes the Answer
Fitting CJ-4 or CK-4 oil incorrectly matters most where after-treatment hardware is involved. Oils formulated for older categories can carry higher SAPS (sulphated ash, phosphorus, sulphur) levels than a DPF or SCR system is designed to tolerate, which shortens after-treatment service life and can trigger regeneration or fault codes. Confirm SAPS compatibility against the after-treatment system fitted, not only the engine’s build year.
Key Differences Between Petrol and Diesel Oils
Diesel and petrol oils are not interchangeable, because the operating conditions they are formulated for differ substantially.
Diesel Oils
- Total Base Number (TBN): higher, to neutralise the acidic combustion by-products diesel engines generate.
- Detergents and dispersants: higher levels, to control soot loading that petrol engines do not produce in comparable volumes.
- Anti-wear additives (ZDDP): run higher, to handle greater mechanical load.
Petrol Oils
- Volatility: minimised, to control oil consumption.
- Sludge and varnish control: tuned for stop-start driving cycles.
- Friction modifiers: included for fuel economy; less relevant to diesel duty cycles.
Using a diesel-rated oil in a petrol application, or the reverse, does not simply under-perform. It is formulated against the wrong failure modes for that engine.
Other Standards Worth Checking
API is not the only classification system in circulation, and OEM specifications frequently sit on top of it rather than replacing it.
ACEA Classifications
ACEA (European Automobile Manufacturers Association) classifications cover petrol (A), light-duty diesel (B), and heavy-duty diesel (E) engines, with a separate low-SAPS category (C) for engines with sensitive after-treatment systems. ACEA testing places more weight on extended drain intervals and after-treatment compatibility than API testing does.
OEM-Specific Standards
OEM-specific standards frequently exceed both API and ACEA minimums for a given manufacturer’s engines. Examples include GM dexos for GM petrol engines, Ford WSS-M2C913-D for specific diesel applications, and Mercedes-Benz MB 229.51. Where an OEM specification is stated on the engine’s data plate or in its service documentation, that specification governs, even where an API- or ACEA-only oil appears to meet a similar description.
Where an oil’s label lists API, ACEA, and an OEM approval number together, it has been tested and licensed against all three. That combination is the strongest verification available before fitting.
Verifying a Licence Before a Bulk Order
To verify a specific oil’s current licence before a bulk order, API’s Engine Oil Licensing and Certification System (EOLCS) directory at api.org lists every formulation currently licensed against each category, searchable by brand and category.
Selecting and Handling Oil
- Confirm the OEM specification first. The engine or equipment manufacturer’s documentation states the minimum API category, ACEA rating where applicable, and viscosity grade required. This takes precedence over a general “compatible with” claim on a product label.
- Match viscosity grade to operating conditions, particularly expected ambient temperature range and load. A correct API category with the wrong viscosity grade still leaves the engine under-protected at start-up or under sustained high load.
- Check after-treatment compatibility for any engine fitted with a DPF, SCR, GPF, or catalytic converter. Confirm low-SAPS or low-ash requirements before fitting an oil that has not been specifically formulated for those systems.
- Weigh synthetic against conventional as a cost-versus-interval decision rather than a performance question. Synthetic oils generally hold viscosity and oxidation resistance better at temperature extremes and support longer drain intervals; conventional oils cost less per service. The right choice depends on duty cycle and the OEM’s stated drain interval for each oil type.
- Monitor with oil analysis. Scheduled oil sampling confirms an oil is still performing at its rated drain interval, rather than assuming the label’s interval holds regardless of duty cycle or operating conditions.
- Store correctly: keep oil sealed, out of direct sunlight, and in a stable temperature environment. Contamination from unsealed containers or mixed products is a common and avoidable cause of premature oil failure.
GFS stocks oils across the current API SN, SP and SQ petrol categories, and CJ-4 and CK-4 diesel categories, including Valvoline and other licensed brands. Use the application lookup to confirm the OEM-specified category and viscosity grade for a specific vehicle or piece of equipment before ordering.
Where API Standards Are Heading
API categories are updated in response to engine hardware changes and tightening emissions requirements, not on a fixed schedule. Two trends are shaping upcoming revisions: continued adoption of low-SAPS chemistry as after-treatment systems become more sensitive, and oil formulations for hybrid drivetrains that must tolerate frequent engine stop-start cycling alongside conventional combustion demands.
API SQ is a working example of that direction: its ultra-low viscosity grades and tightened fuel-economy testing reflect the same fuel-efficiency and emissions pressure now shaping diesel categories.
The practical implication for fleet and workshop buyers is the same one that applies today. Match the oil to the current OEM specification for each engine. Re-check that specification whenever a vehicle or piece of equipment is replaced or updated, rather than assuming the previous oil grade still applies.